Determine the magnitude of the pin reaction at B by (a) ignoring the fact that BD is a two-force member and (b) recognizing the fact that BD is a two-force member. 5.1 2.9 B 2.4 990 lb D. Answer: B = Ib

Q: 3. Determine all forces acting on member ABE of the frame shown. Note: D is a frictionless roller.…

A:

Q: The light right-angle boom which supports the 560-kg cylinder is supported by three cables and a…

A:

Q: he blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB,…

A:

Q: Q. 3) A cylinder weighing 600 N is supported by a pin-connected two-bar frame. Determine the forces…

A:

Q: 1. Solve for the reactions of the truss shown. 100KN 3m 50KN 3m A D 4m 4m 4m 4m

A:

Q: Q2: The structure shown in the diagram ( one ofthe two identical structures that support the scoop…

A: We need to draw FBD and resolve forces first

Q: Determine the horizontal and vertical components of reaction at pin C. Take that P₁ = 450 N and P₂ =…

A: Given that: P1 = 450 N P2 = 540 N It is required to determine the horizontal and vertical component…

Q: 1.25 m N 1.25 m 3m 1.5 m E B G 5 kN 0.751 0.75 m X The rigid L-shaped member ABC is supported by a…

A:

Q: Determine the vertical force P that must be applied at A to maintain the equilibrium of the linkage.

A: Given In this structure supported at B and E To find Magnitude of force P

Q: ray for the paper supply of a photocopy machine is shown. The tray is supported by a single hinge at…

A: Given-Information:- Weight, W = 14 ND = 190 mm  To-Determine:- Reactions at point B

Q: 5. Three cylindrical pipes are supported in a rack as shown below, where the pipes P₁, P₂ and P3…

A: According to the given data P1=100 lb P2=75 lb P3=50 lb We need to find Reaction force at point-B

Q: 5. A plate is subjected to forces as shown below. It is supported by a ball-and-socket joint at A, a…

A: Find the reaction force at A, B and C

Q: 5.6 The metal plate shown is held in position by a pin con- nection at B and a roller at C. Find the…

A: A pin support will exert both horizontal and vertical components of reaction. The support B is pin…

Q: 4 in. 5 in. C G 9 in.- E 45 lb D F -6 in.6 in.- B 120 lb

A:

Q: Determine the components of the reactions at A and B if a 62-lb load

A:

Q: 4. A pipe strut BC is loaded and supported as shown. The strut has a uniform cross section nd a mass…

A: Answer: (a) The tension in the coal is 498.1 N. (b) The reaction at support C is 898 N.

Q: 2. A 200-mm lever and a 240-mm pulley are welded to the axel BE that is supported by bearings at C…

A: Taking moment about C∑Mz=0720200-T120=0T=720×200120T=1200Nso the tension in cord is 1200N

Q: A 200-mm lever and a 240-mm-diameter pulley are welded to the axle BE that is supported by bearings…

A: Now aacording to the above given diagram in the question ∑Mz=0720×200=T×120T=1200 N

Q: Determine the magnitude of the force supported by the pin at C of the loaded frame.

A:

Q: In the structure shown, force F is applied at point A at an angle of 0 in the direction shown. Pins…

A:

Q: A 2600-lb tractor is used to lift 900 lb of gravel. Determine the reaction at each of the two front…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.