Determine the magnitude and direction of the resultant force exerted on this double nozzle by water flowing through it as shown in the figure below. Both nozzle and jet have a velocity of 8.6 m/s and 11.5 m/s. The axis of both nozzles lies in a horizontal plane. 12 cm Jet 17 Cm * 11.5 "/se jet

Determine the magnitude and direction of the resultant force exerted on this double nozzle by water flowing through it as shown in the figure below. Both nozzle and jet have a velocity of 8.6 m/s and 11.5 m/s. The axis of both nozzles lies in a horizontal plane. 12 cm Jet 17 Cm * 11.5 "/se jet

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Subject :Fluid mechanics Give me right solution. Help me urgent
Problem 2. An engineer helps with the design of a rotating spray for a dishwasher. The spray has 4 identical jets spaced equally around the rim of a disc. Water enters though a hollow shaft and then flows radially out to the jets. The nozzle of the jet has a diameter D of 0.3 cm and makes an angle a = I (3 with the horizontal plane of the disc(See figure). The jets are oriented so that v2r=0. If the total flowrate Q=50 mL/s and the disc has radius R= 7.5 cm, determine the torque in dyne-cm required to keep the disc from rotating. Water jet R. Water flows radially inside dise to jet Water in View from top View from side
Problem 6.2 (Page 101) An oil of sp.gr.0.85 is flowing in a stream tube as shown in the figure. The absolute velocity at the inlet and outlet are 15m/s and 25m/s. Determine (i) the components of the velocity at inlet and outlet (ii) Force in x-direction and y-direction (iii) Resultant force (iv) Angle at which resultant force acts. The discharge through the tube is 0.35m/s. The angle at the inlet is 20° and at the outlet is 30°. P1= 3.5 bar, p2=2 bar
the open tank in the figure contains water and is being filled through section 1. Assume incompressible flow. If the water level h is constant, determine the exit velocity V2 for the given data V1 = 3 m/s and Q3 = 0.01 m3/s.
A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1 =0.120 m is given. At a radius of r =0.090 m, absolute flow flows in from the axial direction just before the impeller inlet and relative flow flows out in the axial direction just after the impeller outlet. Assuming a flow rate Q = 0.265 m^3/s, a water density ρ = 1.000 × 103 kg/m^3, a rotation speed n = 2.4 × 10^3 rpm, and a gravitational acceleration g = 9.81 m/s^2 , and assuming that the theoretical head Hth = W/g (W: specific work) derived from Euler's law is constant at all impeller radii, answer the following questions. (1) Find the velocity triangles just before the impeller inlet and just after the impeller outlet at a radius of r =0.09 m.
Help with this practice question
. Indiana Jones needs to ascend a high-rise building. There is a large hose filled with pressurized water hanging down from the building top. He builds a square platform and mounts four 4-cm-diamter nozzles pointing down at each corner. By connecting hose branches, a water jet can be produced from each nozzle. Jones, the platform, and the nozzles have a combined mass of 150 kg. Determine the minimum water jet velocity needed to raise the system.
The jet shown strikes the semicircular vane horizontally. Estimate the horizontal force on the vane. Since this is in British units, use ρ = 1.94 slug/cfs Pls hand written solution
A storm drain has a maximum capacity of 120 L/min. During heavy rains, an influx of 240 L/min approaches the drain. Assuming the drain is cylindrical, by how much would the drain radius need to be increased to handle the heavier rainfall? Assume the water travels at the same linear speed in both drains. The answer is 1.4. Please explain why A 16 times greater B 42 times greater C 2 times greater D 1.4 times greater
What must the gauge pressure p be at A if the volume flow rate out of the pipe at point B is 0.0800 m^3/s?
A water source generates a flow rate of 30 m 3/s in a region of y= 0 with angle zero degree and x=0 with an angle of 90 degree. Determine the magnitude of water velocity V at r= 5 m ( Use pi number =3 and water density =1000 kg/m3)ANSWER: V= 4 m/s
Water flows through a constricted pipe at a uniform rate. At one point, the diameter of the pipe is 0.056 m and the pressure is 5.7 x 104N/m2. At another point, 0.8 m higher than the previous point, the diameter is 0.023 m and the pressure is 1 X 104N/m2 . Calculate the velocities at the lower section and the upper section. Also calculate the rate of flow. Density of water = 1000 kg/m3.