Answered: Determine the LRFD design strength and…

Determine the LRFD design strength and the ASD allowable strength of sections given. A C9 x 20 (Fy = 36 ksi, Fu = 58 ksi) with 2 lines of 7/8-in Ø bolts in the web as shown

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. check the capacity of the shear connection. A992: Fy=50ksi, Fu=65ksi A36: Fy-36ksi, Fu=58ksi…

A: Given Data: A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole…

Q: Determine the design strength of a single C15x50 fastened to a 3/4" gusset plate. Use A36 steel.…

Q: Compute the net area of each of the given members

A: Given information in question Plate dimensions Bolt dimensions Number of Bolts Bolt diameter To…

Q: For the A36 beam shown in the accompanying illustration, what is the required spacing of 7/8-in A307…

A: Consider the free body diagram;

Q: draw -for the tread bars - 3-D 10 mm -for teh iser bars- d 10 mm @150 mm o.c. size of wooden…

A: We need to draw the reinforcement details of tread and riser

Q: Determine the design capacity of the given tension member. Assume that the slenderness requirement…

Q: 4. Determine the minimum net area of the angle section having a bolt hole with a clearance of 4mm.…

Q: Determine the net tensile area for the connection plate shown. Use a 3/8" plate with 3/4" bolts with…

A: Given data, Plate thickness (t)= (3/8) = inches Bolt dia = (3/4) inches So, hole diameter= dh =…

Q: ¿A Tension member has used to resist load of 65 kips, and the shear stress on bolts is 15.9 kips.…

A: If two or more plates are to be joined then the bolts or welding is used. The applied shear stress…

Q: Q17 An L4x4x7/16 tension member is connected with %"Ø bolts, as shown in the figure below. Both legs…

A: Given Data: The size of the tension member is L4×4×716. The diameter of the bolt is 34". To…

Q: Angle Bolted Connection. The L6 x 31/2 × 5/16. -in angles, shown in Figure, The bolts are 3/4 inch…

Q: A double angle shape (L5 x 3 x 5/16) is shown below. The steel is A36 and the holes are for ½ in…

Q: 2 in 3 in ... Determine the LRFD design strength and the ASD allowable strength of sections given.…

Q: Compute the net area. The 1 x 10 plate shown in Fig. P3-10.The holes are for 7/8-in Ø bolts.

A: The calculation of the net area An of the plate is given by - An = Bt - nϕht + nss24ghere,B =…

Q: CLO3: Determine the tensile capacity of the 1/2-in. by 7-in. plate shown in Figure bellow. The…

A: Given: The cross-section of the plate is ½ in x 7 in. The diameter of the bolt is 6/8 in. The value…

Q: Design a connection for the following conditions: 2L 8x6xtension member • Dead load = 50 kips, live…

A: Given data: DL = 50 kips LL = 100 kips Group A bolts, no-slip permitted. 3/8 in thick gusset plate A…

Q: Compute the net area of each of the given members

A: Given data in question Plate dimensions Bolt diameter Staggered bolting To find out Net area of…

Q: ーL7x4x} 1号in。 3 in 2号in 3 in 4 2 in

Q: in Ø bolts W12 x 40

Q: Q3) Determine the total number of 3/4-inch, A325 bolts required for the tension splice in Figure.…

A: Solution

Q: Calculate the critical net area (mm²) for the tension member shown. The bolts are M22. 40 65 90 115…

A: Given A tension member Required Net area

Q: Prob. No. 4-11 PD PL Length Section (kips) (kips) (ft) 175 26 W12 150 Steel A36 End Connection Two…

Q: a 3" oj ob C" OC 5" of od 3" e = 4" A" B" | A" B" A" B" The holes are for 1-inch-diameter bolts.…

Q: Hhello, Thanks a lot for your help, please I have the following points: 1-Is it allowed to use…

A: Design of tension member

Q: Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes…

Q: Determine the avaiable 2" streugth of 34" 3" 2 A325 -N bolts in 1.25 3" 3" 1.25" the lap splice with

A: The given data is: A 325-N bolts-with 3/4 diameter. The dimensions of the section is shown in…

Q: Problem 2: For the Channel as shown in the figure below determine the design and allowable strength.…

A: We have to determine the value of design and allowable strength. The holes are for 18 mm diameter…

Q: Two plates each with thickness t = 10 mm are bolted together with 6 - 16 mm diameter bolts forming a…

A: The thickness of the plates = 10 mm The connection provided = 6-16 mm bolts The yield strength of…

Q: ple shear stress FT = 207 MPa. Use A36 steel with yield strength Fy = 248 MPa and a minimum tens h…

A: According to given data A butt joint is bolted using A325 bolts with a diameter of 22mm, with…

Q: Compute A,, and A, for a 14-in.-wide and ½-in.-thick plate subject to tensile loading with staggered…

A: Given : Width = 14 inches Thickness = 1/2 inches Compute An and Ae for the given plate ?

Q: Drawing B INSTRUCTIONS: USE M12 BOLTS GRADE 4.6/5 INCLUDE BOLT GAUGE DISTANCES AND EDGE DISTANCES…

A: Planning is the process of setting goals, defining strategies, and outlining the steps or actions…

Q: 3. A36 steel and 7/8 in diameter bolts [ 2-MC12 × 40 ㅇㅇㅇ All 2 in 2 - in 32 in 31 in 2 - in

Q: Determine the LRFD design strength and the ASD allowable strength of sections given. Neglect block…

A: Answer We know that minimum strength given by gross section yielding or Net section ruture strength…

Q: 9.0 A C12 x 30 is connected with 25 mm diameter bolts in each flange, as shown. If Fy= 345 MPa, Fu=…

Q: The 1 × 8 plate is shown in the figure. The holes are for 3/4-in Ø bolts. Compute the net area of…

A: Given that, width of plate, B = 8 in the thickness of the plate, t=1 in diameter of the bolt, d=…

Q: 1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads…

A: The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Q: subject

Q: GROSS AREA, NET AREA AND EFFECTIVE NET AREA APPLICATIONS: Problem 2-9 A single lap joint is shown in…

A: 1.Gross Area Ag=wg×twhere,wg=width of plate 1t=thickness of plate 1…

Q: Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes…

Q: Compute the net area of each of the given members.

A: Dimension of the plate=3/5 x 10 in2 Dia of the bolt ,d=1inch Line of bolts,n=1

Q: EE- 3 in 3 in 8 in $ 2 in |1 in PL 1 × 8 The holes are for 3/4 -in Ø bolts

A: A plate is given we need to find out net area

Question

Determine the LRFD design strength and the ASD allowable strength of sections given. A C9 x 20 (Fy = 36 ksi, Fu = 58 ksi) with 2 lines of 7/8-in Ø bolts in the web as
shown

2 in
34 in
C9 x 20
3 in 3 in
FIGURE P3-31
2.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use NSCP specifications and assume a double row of bolts with standardsize holes for a bearing type connection with threads excluded from the shear planes.Minimum tensile strength Fu = 552.93MPa. Assume diameter hole is 3mm bigger than thediameter of bolts. Allowable shear stress is Fv = 207MPa. Allowable bearing stress fb = 1.2Fu.Diameter of bolts is 19mm. Fy = 449.25MPa.(a) Compute the tensile capacity of the steel plates. (Max. Net Area = 0.85 of Gross Area)(b) Compute the number of 19mm diameter bolts to develop the full strength of the plates. Note: SHOW DRAWINGS AND SOLUTIONS.
Two steel plate tension members have been connected using 0.72 inch diameter bolts arranged in an equally-spaced 9 by 3 rectangular formation. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 51.2 ksi, clear distance for each edge bolt as 0.12 in, and the clear distance for the other bolts as 1.072 in. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load and live load assuming live load is half as much as dead load. Consider ASD.
Which of the following gives the minimum number bolts that can be accommodated in one row of a 350mm flat plate. O 4 O 5 O 6 O 7
A C15x40 channel section is bolted to a gusset plate is used to resist a tensile loadPu =313 k. The bolts are 3/4 inch  diameter bolts A325 N (Group A, N Type) used insingle shear to resist this load. The bolts are to be symmetric and arranged in 3 rows.1) Determine the number of bolts needed for this connection. Draw a detailshowing how the bolts are arranged and showing spacing and edge distances onthis connection. Assume edge distance Le = 1.75db , use Le to nearest 1/4 in.2) If the connection is to be replaced by a fillet welded connection with transversewelds only along the channel web, determine the required fillet size to thenearest 16th of an inch.
1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g g 19mm 178mm L 178 x 102 x 19 Gusset Plate
1. In the butt joint shown below, the 7/8-inch diameter boits are made of A325 steel with threads excluded from the shear piane and the plates are made of A36 steel. o of a Determine the bolt shear strength b) Determine the bearing strength of the plate ) Determine the tensile strength (both gross and net) of the plate d) What is the strength of the bolted connection?
Please answer with complete details. Thank you. A = 1 B = 1 C = 2
Compute the net area of each given members. 1. PLx 8 in Ø bolts 2. in O bolts W12 x 40- -PL를 x 14 3. WT15 x 45
In mm) Problem 8: A C310 × 45 is connected with 25mm diameter bolts in each flange, as shown in Figure, Problem 11. If Fy = 345MPA, Fu = 450MPA, and Ae = 0.90An, Apply the following %3D %3D %3D approaches to determine: a. The design strength for LRFD. b. The allowable strength for ASD. Section Figure. Problem 8
Consider the following bolted connection. Slippage is permitted. Member: L6x6x3/4 3/16 “ gusset plate Pu Pu A36 steel 3.5* 1"diameter A325-X bolts 1 1/4" 3 " 3* 1 1/4" Question 3.1: Please, indicate if the combined bolt shear strength is closer to: Question 3.2: Please, indicate if the combined bolt bearing strength is closer to: Question 3.3: Please, indicate if the angle yielding strength is closer to: Question 3.4: Please, indicate if the angle fracture strength is closer to: Question 3.5: Please, indicate if the angle block shear strength is closer to: Question 3.6: Please, indicate if the overall connection strength is closer to:
An industrial plant emits lead at 300 g/s from a 50 m high stack at 300°C with a stack velocity of 12 m/s. The stack diameter is 2 m. The wind speed is 5.0 m/s, the air temperature is 10°C, the atmospheric stability class is C, and the atmospheric pressure of 102 kPa. What is the effective stack height?
Compute the net area. The plate 7/8 x 14 shown in Fig. P3-11. The holes are for 7/8-in Ø bolts.