Determine the internal normal force, shear force, and moment at point E. Remember that cables or strings can only be in tension. Assume distributed load 'w as the last non-zero digit of your student number mulitplied by 100 N/m. E.g. if you student no, is 11223304, then w =4*100 = 400 N/m E. D. w N/m -1.5m- 15m-1.5m-1.5m

Q: cos x -sin x CoS X 1. 01 0, show that f(a)ƒ(b) = f (a + b). 5. If f(x) = | sin x %3D

A:

Q: 2. tan r +tan z = sin z cos z

A:

Q: 1. Three streams flow towards Matuno River. The watersheds through which the water flows have…

A: Chemical mixing Formulae for two or more mixing

Q: 4 A wire 28 m piece to form a How should the wire be cut :long is to be cut into two pieces, one…

A:

Q: I mec = 12 58 cm 1258 h = 2 4 6x h² 12

A: The moment of Inertia of rectangular cross-section Imec = 1258 cm4

Q: State whether the equation is ordinary or partial, linear or nonlinear and determine its order and…

A: To verify that y is a solution of a differential equation, substitute y in the given differential…

Q: Find the solution of the following differential equation

A:

Q: Fastly calculate the value of displacement Work done=20 J force%33 N

A:

Q: Prove the following relation: e Yw 1 + e Gs a. Yd=Ysat b. Yd= (Ysat-Yw) Gs-1

A:

Q: Obtain the general solution of the DE: (xy + x) dx = (x²y² + x² + y² + 1) dy x)dx…

A: Given data: xy+xdx=x2y2+x2+y2+1dy

Q: Solve the differential equation (x + sin y) dx + (xcosy-2y)dy=0 (A) B 2 2 +xsiny=c +ysinx=c Ⓒ+² 2…

A: Solution: Given: The differential equation: (x+siny)dx+(x cosy-2y)dy=0 Check for exact equation: The…

Q: Q2: use the inverse method to find the vlaue of X, Y and Z for the follwing equations: 2x-y+223D1…

A:

Q: dy Find using logarithmic differentiation if y = %3D dx Va²+4

A: To determine the value of dydx for given function using logarithmic differentiation.   Given:…

Q: What reduction factor are we going to use if p > Pb a. 0.9 b. 0.65 c. 0.45 d. Ø= 0.65 +0.25 Ey Et…

A: Given:-ρ>ρbTo find:-reduction factor

Q: 2. Find P, Q, and C if R = 75000 N.mm у 100 N 12 A 30 mm 400 N 3 t -30 mm B

A:

Q: Problem 1 Determine the vertical displacement at joint H of the truss below using the method of…

A: Given: Area of the member, A = 4.5 in2 Modulus of elasticity, E = 29000 ksi To find: Vertical…

Q: Determine the vertical displacement at point C of the frame below using the method of virtual work.…

A:

Q: Q1- : Water flows out of a lake into steep slope wide rectangular channel (n = 0.017) as shown…

A: Draw the given section:

Q: QI: Find the general solution of the differential equation y" + 4y' + 5y = 0.

A:

Q: Solve using nevilles method at x=6 asap

A:

Q: Draw ILD for V in the following figure & write equation of А ILD for VA A TTTTTTT 6 m C 6m 18 m D 6m…

A:

Q: Solution must be accompanied by free body diagram 3. Resolve the forces into X and Y components.…

A: To find x and y components of force

Q: No elements selected 75 N/m 800 N- m 8m L.

A:

Q: A double angle is used as the top chord of a given truss shown in figure 17.7. It is composed of 2 -…

A:

Q: What are the classifications of foundation

A: Foundation is the main component of a structure that connects the structure to the ground. The…

Q: Find the correct solution in finding the general solution of the given differential equation. xdx –…

A:

Q: 1+sina 2 seco 4. 1+ sin o

A: Prove the identity

Q: Using DIM, solve for: a. Ymax (mm) b. A (rad) Use E = 200 GPa. 90 167 kN kN/m 165 kN P 120 kN.m L…

A:

Q: Which among the following determines the direction of closing error? O a. Tan δ = Σ/ΣΟ b. Tan 8 =…

A: A closing error is a distance that failed to close the end of the traverse line with its starting…

Q: Here are two statements: Statement 1: Figure F is a rectangle. Statement 2: Figure F is a triangle.…

A: in this question a statement is given

Q: B 6 m | 20 KN FIND THE VALUE OF Mmax

A:

Q: 220. Suppose f(x, y) = x+y, u = e* sin y, x = 1², and y=nt, where x=rcos and y=r sin 8. Find af де

A:

Q: The water sprinkler, which is located at the base of a hill, emits a spray of water with a velocity…

A: Introduction- Sprayer watering is a method of irrigation that uses a watering approach similar to…

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.