Determine the force in member DE of the truss shown. State if the members are in tension or compression.

Q: A. ADJUST THE GIVEN CLOSED COMPASS TRAVERSE LINE LENGTH OBSERVED BEARINGS FORWARD BACKWARD STA…

A:

Q: We found that the Reynolds and Froude numbers Were important? discuss it

A: Reynolds number Froudes number Both numbers are widely used in fluid behaviour study.

Q: How to convert a value from the kips unit to a value in the ib unit

A: Brief concept introduction- Kips and lb are the two major units that are used for the measurement of…

Q: If the value of the atmospheric pressure reading using the barometric gauge is (750 mm) and the…

A:

Q: A soil sample having a void ratio of 1.3, water content of 50% and a specific gravity of 2.60, is in…

A:

Q: a) Identify and locate the centroid, ỹ on axis x'- x' for the parts cross-sectional area in Figure…

A: Find centroid Y and moment of inertia about X'X' axis

Q: Q- For each of the following statements, choose the correct (A,B,C,D) 1. Hydrograph is a graphical…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: 5. What happens to the depth of flow when there is an obstruction in the path? a) Remains the same…

A: To find : Effect on depth of flow when there is interaction.

Q: draw a diagram for three Cafeteria objects sharing the same opening and closing times?

A: The cefetaria diagram is given below,

Q: 2. What is v2/2 in the equation for a control volume in space? a) Potential energy per unit mass b)…

A: Answer: b Explanation: According to the 1st law of thermodynamics, the equation for the control…

Q: 2. Changes in the behaviour of the jump can be observed by changing the a) Temperature

A: To find : Change in behavior can be observed by changing.

Q: The matter proceeds further. The Arbitral Tribunal meets with the parties at the Preliminary Meeting…

A: Part a Verbieste  requests to amend the pleadings of the claim must not be allowed by the tribunal…

Q: · A cantilevered beam is part of an assembly machine and is made of steel with round cross section…

A: Given 400lbf= 1780N

Q: 900 N/m 500 N/m 4 m 3m a. Draw the free-body diagram. b. Find the reactions at A and B.

A:

Q: 8. What is the relation between kinetic energy and momentum? a) p=m/v b) p=mva c) p=mv d) p=m

A:

Q: Which type of roller is most suitable for soil compaction? a) Smooth roller b) Sheep foot roller c)…

A: Sheep foot roller is the best roller for compaction . This is due to the action of roller which…

Q: 6m, calculate the hydraulic depth of the channel.

A: To find : Hydraulic depth.

Q: mine the resultant couple e into x and y components and g the and y -2 ft t nts 1 ft 80 lb 80 lb S S…

A:

Q: Determine the reactions at A for the cantilever beam subjected to the distributed and concentrated…

A:

Q: 8. Determine the centre of pressure on an isosceles triangle plate of base 6m and altitude 6m when…

A: The study of fluid behaviour (liquids, gases, blood, and plasmas) at rest and in motion is known as…

Q: The soil that is formed by the action of wind is called a) Lacustrine soil b) Alluvial soil c)…

A: Soil formed by action of river is called alluvial soil. Soil formed by action of lake is called…

Q: The table below lists data used in obtaining a mix design for an asphalt concrete paving mixture. If…

A:

Q: 40 30 20 20 15+ 10 10 10 15 20 25 30 Air temperature, "C 35 Wind velocity, km/h 4 40 35 30 25 20 15…

A: Calculate the rate of evaporation from the following equation: E=5(Tc+18)2.5-r(Ta+18)2.5V+4×10-6…

Q: QI: The Results Of A Sand Cone Test Are Shown Below: Jar + cone (before test) = 7698 gm Jar + cone…

A: Field dry density of the sand = γbulk1+w Here,             w  = water content of the sand = 6% or…

Q: Calculate the maximum depth at which the depth of a circular tunnel can be dug in a k with the…

A: Stress concentration: A stress concentration is a part of an object where the stress is much higher…

Q: ex a solid shaft is subjected to a torque of 1-6 kN.m find the necessary diameter of the shaft. if…

A:

Q: 1. Estimate the hydraulic depth for a most economical circular channel section in case of maximum…

A: To find : Hydraulic depth.

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

A:

Plane and Space Trusses

In civil engineering, a truss is the most important structure that forms the most fundamental member of any building structure and commercial complexes. Trusses are composed of individual members or links that are interconnected by suitable joints, such as rivets, welds, or bolts, and nuts. In trusses, the interconnection leads to the formation of a series of triangles joined together such that all the triangular members behave as a single rigid body. In a simple truss, three members are connected to form a truss member. In trusses, the force always acts at the joints or the interconnection between the individual members.