Determine the flow in L/s into or out of eachreservoir in the pipe system shown; Use n = 0.011for all pipesL=1200 m; L2= 900 m; La= 1500 m;Di= 30 cm; D; = 20 cm; D3 = 15 cm%3D%3DEl 30 mEl 24 m1El 15 mEl 0 mB.3.

Answered: Image /qna-images/answer/d4aebe6d-fdf0-47a7-94cc-7a6a41c0c3a1.jpg

Determine the flow in L/s into or out of each eservoir in the pipe system shown; Use n = 0.011 or all pipes %3D L-1200 m; = 900 m; La 1500 m; D=30 cm; Dz 20 cm; D3 = 15 cm El 30 m A El 24 m 1 El 15 m El 0m 3

Determine the flow in L/s into or out of each eservoir in the pipe system shown; Use n = 0.011 or all pipes %3D L-1200 m; = 900 m; La 1500 m; D=30 cm; Dz 20 cm; D3 = 15 cm El 30 m A El 24 m 1 El 15 m El 0m 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7) A pump has the following characteristic: Volume flow rate 23 46 69 92 115 (m³/h) Head (m) 17 16 13.5 10.5 6.6 The is used to pump water from a lower tank to a higher tank through a total length of pump 800 m of 150 mm diameter pipe. The difference between the water levels in the two tanks is 8m. Neglecting all losses except friction and assuming that C; = 0.004, find the rate of flow between the two reservoirs. [Ans: = 60m/hr]
5.3 Water flows upward through the pipe reducer shown. The elevation difference betwoen points / and 2 is 4z. If the pressure gage mounted at point / reads gage pressure p, determine the volume low rate Q in m/sec. Take the following data: Mercury A 18m d- 100 mw a - 70 mm L- 180 mw a - 300 PS8 bar D - 200 mm If the water flow is reversed downward having the same volume flow rate calculated previously Q, determine the new inclined manometer reading, what do you notice.
A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e-0.026mm, v1.13" 10 m?/sec). Fig(1) 6m 23m Fig.(1) Nozzle
Q.10. The flow net below represents air flowing over a small hill. 1.8m .d 1.5m 1.2m 0.9m • a 2m At the inlet, the streamlines are evenly spaced 2 m apart, and the air flow is a uniform 3 m/s. a. Taking the ground to be = 0 m²/s, what are the values of the streamlines A-C? b. Find the air flow speed, and the corresponding gauge pressure, at each of the points a-d at the crest of the hill. c. The stream and potential lines have been drawn to be approximately square. As- suming this to be the case, what is the value of the potential drop Aø1 and A¢2.
Please fast only final answer needed
Ex5:- From Figure shown, the pipe line have Qa = 15L/s, QB = 3QD, DA=100 mm, DB= Dc = 25mm, Dp= 50 mm and vc = 4m/s. Find the value of discharge and velocities for pipes A, B, C and D? %3D
Please show complete diagrams and solutions T.Y :) Use Bernoulli's Energy Equation Dislike if not followed A 24 in. pipe conducts water from reservoir A to a pressure turbine (elev. = 15'), which discharges through another 24 in. pipe into tailrace B (elev. = 0'). The loss of head from A to 1 is 5 times the velocity head in the pipe and the loss of head from 2 to B is 0.2 times the velocity head in the pipe. What must water surface elevation at the reservoir be maintained such that the energy given up in the turbine is 552 hp? Assume discharge equals 25 cfs. Express all dimensions in English units.
Please try to solve it within 30 minutes
None
3.7 m 4 cm 3 diameter Group (D) 7.2 m Determine the discharge, the velocity of flow and pressure at the point (2)?
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
Q5