Determine the ffg: • Support Reactions, ● Shear and Moment Equations. For the last segment use the right section, the FBD Shear and Moment Ordinates, use Relationship between the Load, Shear & Moment Diagram, Draw the Shear and Moment Diagrams, ● If Any, Locate the Position of the Point of Zero Shear, Point of Inflection and magnitude & location of the maximum moment. W1 A -L1 B -L2 U VALUES: SET L1 L2 P1 P2 W1 W2 B F (6) 4 3 4 5 6

Determine the ffg: • Support Reactions, ● Shear and Moment Equations. For the last segment use the right section, the FBD Shear and Moment Ordinates, use Relationship between the Load, Shear & Moment Diagram, Draw the Shear and Moment Diagrams, ● If Any, Locate the Position of the Point of Zero Shear, Point of Inflection and magnitude & location of the maximum moment. W1 A -L1 B -L2 U VALUES: SET L1 L2 P1 P2 W1 W2 B F (6) 4 3 4 5 6

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part C please
Given the following, Construct the load, shear, and moment diagram. please solve it using the right approach and please show all your work
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given beam and loading. Given: P = 5.5 kips. دلالی 6 kip-ft A V\max M\max kips C kip.ft 6 ft P 3 kips 4 kips. D E 6 ft Determine the maximum absolute values of the shear and bending moment. 6 ft 6 ft 12 kip.ft B
w2
Completely solve both problems. WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS. In the figure below, determine the maximum shear and moment, and draw the shear and moment.
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Strength of Materials
subj: civil engineering A 50-mm diameter bar is used as a simply supported beam 3 m long. The flexural stress is limited to 50 MPa. If w = 36. •Find Fb(bottom) and Ft(top). (F = Mc/I) •Plot the flexural stress and draw a shear & moment diagram.
ID No:.. Name: Use the method of virtual work and determine the maximum allowed load P so the maximum horizontal displacement of point C should not exceed 5 mm. Each steel member has a cross-sectional area of 1200 mm?. E=200 GPa. 4 m 3 m
M:20 L:1.9 P:23 w: 17
Part II. Beams 4. Draw the shear and moment diagrams for the loaded cantilever beam where the end couple M1 is adjusted so as to produce zero moment at the fixed end of the beam. Then answer the questions: a. at x = 1 ft, V = ? and M=? b. at x = 6.9 ft, V=? and M=? c. What is the maximum (absolute value) shear? d. What is the maximum (absolute value) moment? 440 lb/ft 5.1' 5.1' M₁
ANSWER TYPEWRITTEN FOR UPVOTE. SKIP IF YOU ALREADY DID THIS OR ELSE DOWNVOTE
1. Two members, each consisting of straight and 168-mm radius quarter-circle, are connected as shown and support a 500-N load at D. Draw the FBD of the entire frame and members ABC 168 mm 168 mm A and DBC, including dimensions. Determine the forces in member ABC. Also, calculate the force exerted by member DBC on pin C. B D 100'mm 500 NV +54 mm -252 mm -324 mm Answers: Ax = 275 N→, Ay = 390.625 N ↑, By = 600N Į, ABCX = 375N +, ABCY = 209.375 N↑; DBCX = 0, DBCY = 100 N↑ %3D %3D %3D