Determine the equivalent state of stress on an element at the samepoint oriented 60° clockwise with respect to the element shown in thefigure below. Suppose that o, = 146 MPa ,ay = 101 MPa.(Figure 1)36.1MPaSubmitPrevious Answers Request AnswerX Incorrect; Try Again; 4 attempts remainingPart BDetermine oy.Express your answer to three significant figures and includeHA?Oy =ValueUnitsSubmitRequest AnswerFigure1 of 1Part CDetermine Tey -Express your answer to three significant figures and include75 MPaHẢ?ValueUnitsSubmitRequest Answer

Answered: Image /qna-images/answer/44e27f0a-5475-4139-9923-6b93e76d02a7.jpg

Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with respect to the element shown in the figure below. Suppose that a, = 146 MPa , ay = 101 MPa (Figure 1)

Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with respect to the element shown in the figure below. Suppose that a, = 146 MPa , ay = 101 MPa (Figure 1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The general stress element is loaded such that τxy = 25 MPa. Using Mohr’s circle, find out the maximum normal stress and shear stress acting on this element. (Pure torsion) (Please elaborate what is pure torsion means.)
We have the plane stress state shown in the figure. You are asked to determine the stress components acting on the inclined plane AB. σx'=? σy'=? τx'y'=?
The state of plane stress shown occurs at a critical point of a metal machine component. As a result of several tensile tests, it has been found that the tensile yield strength is Fy for the grade of metal used. Determine the ratio of OT/ OH shown in the figure, using the maximum-shearing-stress criterion (Tresca Hexagon). (Using Mohr circle method to calculate principle and average stresses) OX TXy Mpa Mpa Mpa MPa ob σy тху 90 -60 45 310 dy OX x Sx=Sx Sy=sy txy=txy Fy=Yield Strength Answer
N = 400 N T= 1.8 N-m In order to drill an 8mm hole into a block of steel, a Normal Load of 400N and Torque of 1.8 N-m must be applied to a drill bit. The drill bit H D = 8mm has a diameter of 8mm and is a solid cylinder at point H. Write the stress state for the element H pictured in the diagram.
A state of plane stress is illustrated in the stress element in Figure 3. (a) (b) 30 MPa Figure 3. 40 MPa 60 MPa y X Find the center, X and Y of the Mohr circle. Plot the Mohr circle using these points. From the Mohr circle, find the principal stress and the maximum shear stress. Indicate on the Mohr circle where these values are found.
For the flat stress state shown in the figure. Use Mohr's circle to determine (show the procedure only with the use of geometry): a. Draw Mohr's circle indicating coordinates of the points that represent the given stress state, center, radius, coordinates of the points that represent the state the maximum and minimum normal stresses, coordinates of the maximum shear and angle of rotation from the stress given to the plane principal. b. Use the results of literal a to draw the element subjected to main forces and the element subjected to maximum shear. 12 MPa 19 MPа y 19 MPа 46 MPа 46 MPа 19 MPа 19 MPа 12 MPa
The solid shaft is fixed in the wall at A (Figure Q2). A force F is applied at B, determine a) the stress components at points D and E, b) the principal stress at each of these points. (Draw free body diagram to show all loading forces and moments) Take F = 12 N and 0 = 45°. 1,25 mm 6 mm. 8 mm. 3 mm B F Figure Q2
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
Grandpa/Shutterstock.com 7.3-26 An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to stresses of σ = -45 MPa and 7xy = 39 MPa (see figure). It is known that one of the principal stresses equals 41 MPa in tension. (a) Determine the stress o,. (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented element. PROBLEM 7.3-26 T P o, Т 139 MPa 45 MPa
Q-1 Figure Q-1, below, shows Mohr’s circle for a point in a physical object that is subjected to plane stress. Determine the stresses σx, σy, and τxy, and show them on a stress element, properly oriented with reference to x-y axes. Determine the principal stresses σ1, σ2, and τmax and show them on a stress element properly rotated with respect to the x–y element Determine the stresses σn, σt, and τnt, and show them on a stress element that is properly rotated with respect to the x–y The sketches must include the magnitude of the angles w.r.t. positive x-axis as well as the angle between the x and n axes, and an indication of the direction of rotations (i.e., either clockwise (c.w.) or counterclockwise (c.c.w.)).
An element in plane stressis subjected to stresses σx, σy, and τxy (see figure).Using Mohr’s circle, determine (a) the principalstresses and (b) the maximum shear stresses and associatednormal stresses. Show all results on sketches ofproperly oriented elements. σx =-29.5MPa, σy = 29.5MPa, τxy= 27MPa
At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition, (i) determine the normal and shear stress acting on the inclined plane (ii) calculate the principle angle and the shear angle