Determine the equivalent impedence for the circuit below. Given R2-50, w-211, C-1F, L=12H. Put the answer in polar form (magna and enter the magnitude for your answer with 3 significant digits in polar form (For example, if your answer was 43 2546@45 8 degm wanting you to enter 4.33e+1) 0 mo R₂

Q: A Buck converter has the following parameter. Vin =10V, Vout=4V, Pout=10W. Fsw=100kHz. The parasitic…

A: The given information about a Buck converter is shown below. Volts.  Volts. W. kHz.

Q: A JFET with IDSS= 9.71 mA and VGSoff=-5V. The drain current when VGS=-2.69 V is

A:

Q: The A/D converters add a significant cost to the system. True False

A: In this questions, we need to tell about the ADC is expensive or cheaper.

Q: Which DMM measurement would you expect based upon the red and black leads in this image? O OV O 2.5…

A: In this question,  We need to choose the correct option What is reading of the voltmeter.  We know…

Q: Variac Input R Output

A: Auto transformer: It is a device consists of a single winding which is used to vary the voltage of…

Q: Consider the circuit in (Figure 1) and take v = 8 V and i = 0.7 A. Figure • 40 Ω ע 150 Ω ww + vΣ 100…

A:

Q: The series circuit is an energy converter . into what type of energy is the electrical energy…

A: Given: Series circuit converter

Q: Employing the characteristic curve in Figure 1 and obtain the design for a voltage divider…

A:

Q: What is the power consumed by the 50Ohm resitor when it is connected in series with the 50V source?

A: When the resistor connected in series with the voltage source only then the voltage across the…

Q: Determine the Q-point for following circuit. Also find new Q-point if value of B changes to 150.…

A:

Q: Innovative ideas to reduce energy consumption in communution circuit

A: To explain  the  reduce energy consumption in communution circuit

Q: O in the circuit fo

A:

Q: Create an 8 way multiplexer using only the 2 way multiplexers.

A:

Q: For the circuit shown in Figure 5, if R C = 4 KN, RL= 4KN, R in=0.5 KN, IB = 50 µA and IC = 5 mA, а.…

A: Given:RC=4 kΩRL=4 kΩRin=0.5 kΩIB=50 μAIC=5 mAVin=10mV

Q: Simplify to a sum of three terms: A'C'D' + AC' + BCD + A'CD' + A'BC + AB'C'

A: Given To simplify to sum of three terms

Q: In the figure circuit voltage divider what is the (RC,RE,R1,R2) to get the best possible Q-Point at…

A:

Q: QL. Three resistors are corinected in series to a (220 V)supp! The combined voltage drop across CRi)…

A:

Q: Interference signals from outside of a difference amp circuit can be mitigated by using proper and A…

A: When interference signals came from outside of a difference amp circuit can be reduced by using…

Q: choose the correct answer 4-If the voltage generator is 5 mV in an emitter follower, the output…

A: Input voltage of emitter follower circuit is given, Vin=5 mV

Q: Construct an Multiplexer 8*1 with two Multiplexer 4*1 and additional gate .

A:

Q: 5. For the circuit in Figure 30–1C, if R, and R2 are 10 k2, the LED is lit when the input voltage is…

A:

Q: +9 V 8.3 V – KQ2 B2 = 100 Vout KQi B1 = 100 + Vin VBE - FIGURE 5-69 (Exercise 5-18)

A: First we will find out the collector current then output impedance for both bjt then by ac analysis…

Q: (d) Calculate the average output voltage. (e) Calculate the average current flowing through the load…

A:

Q: What are the advantages of a parallel-series combination circuit over pure series or pure parallel

A: To answer above problem, one should know about equivalent resistance for series and parallel…

Q: If VCC = +18 V, voltage-divider resistor R1 is 4.7 kOhms, and R2 is 1500ohms, then the base bias…

A:

Q: The figure below shows the step function, so the Parameters setting of the step block are: Time…

A: Generally there are 4 types of signals we used in control system.  1. Impulse signal 2. Step signal…

Q: in the Blanks For an n-channel JFET, Vgs can vary from ____ to Vgs(off)

A: In n-channel voltage Gate to Source is reverse biased. Also gate has very high input impedance due…

Q: RCDS are used to protect circuits from O over current faults O under voltage faults O over voltage…

A: RCD ( Residual-current device) :  RCD is an protective device which cut power supply within 10 mili…

Q: single phase full converter

A:

Q: If VCC = +18 V, voltage-divider resistor R1 is 4.7 kOhms, and R2 is 1500ohms, then the base bias…

A: The solution is given below

Q: Design asynchronuus counter Mod 14

A: Given, To design a 14 mode asynchronous counter

Q: for part iii The quiescent output voltage is 10V as in part (a), and the supply voltage VCC is 20V.

A: Step 1:Step 2:Step 3:

Q: Derive the Stability Factors for the voltage divider bias configuration *

A:

Q: How is the phase-controlled thyristor turned on? Select one: O a. A gate current is applied with VAK…

A: The solution is given below

Q: What is the current divide formula

A: The obstruction offered to the flow of current is called resistance and the electrical element that…

Q: What is the half subtractor

A: Half Subtractor Definition: The Half Subtractor is a combinational circuit which processes the…

Q: The hardware systems operate under a static discipline with the following voltage thresholds…

A: Given, VIL =2.8V VIH =3.5V VOL =1.3V VOH =4.1V

Q: What happens to the circuit current when the frequency is increasing in an RL Circuit? Explain.…

A:

Q: In what region the following circuit will be in? +1.8 V o VD O a. Triode O b. None- off the options…

A: We need to select correct option for given circuit.

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.