Determine the correcthorizontal distance AE when it was measured AB = 45m, BC= 38m, CD= 55m, DE =42.58, with difference of elevation per measurement as follows: 0.3m, 0.55m, 0.45m, 0.35m, measured with a 30-m tape under a steady pull of 6.5 kg at a mean temperature of 300C. If the tape used is of standard length at 200C under a pull of 5.5kg with a cross-sectional area of 0.025cm2, elastic modulus as 2.10x106kg/cm2, coefficient of thermal expansion to be 0.0000116/10C and weight of tape is 0.5kg.

Q: A line was measured using a tape that is suspended with a pull of 145 N on both ends. The mean…

A:

Q: 1. The taped distance of a line was 99.812 m using a 100 m steel tape weighing 2 kg at a pull of 10…

A:

Q: LEASE ANSWER WITH COMPLETE SOLUTION. THANK YOU. The horizontal distance between two points, A and B…

A:

Q: A stadia rod held at a distant point B is sighted by an instrument set up at A. Determine the length…

A: Solution:-

Q: Determine the radius of gyration of the shaded area with respect to the specified y axis. (Answer…

A:

Q: Q2/ Readings obtained from a two peg test carried out on an automatic level with a staff placed on…

A:

Q: SITUATION B: Prepare and complete the profile level notes for the information shown and perform the…

A:

Q: 7. A horizontal collimation test is performed on an automatic level. With the instrument setup at…

A:

Q: A Civil Engineer used a 50m tape in measuring an inclined distance. The measured length on the slope…

A:

Q: A Civil Engineer used a 40m tape in measuring an inclined distance. The measured length on the slope…

A:

Q: NSTRUCTIONS. PLEASE ROUND OFF ONLY THE FINAL ANSWERS. An Engineer used a 30 m tape in measuring an…

A: Error=CPull+Ctemp-Csag-CslopeCPull=(P-Po)(L)AECTemp=Lα(δT)Csag=W2L24P2CSlope=h22L

Q: H.W/ A longitudinal section survey was conducted for the purpose of implementation of two sewer…

A: Given, Elevation of BM1 = 132.230 We know that, HI=RL+BSRL=HI-ISRL=HI-FS Here RL is the elevation,…

Q: You have been given the following constant-head data for planar flow of water in a 1.5-mm thick…

A: Given data- Constant-head data for the planar flow of water- Discharge(Q) Q=21 cm3/minHead loss (HL)…

Q: A steel tape having a standardized length of 29.990 m, with 8 kg tension, at 20°C, and  supported at…

A:

Q: 2. A 30m tape has the following condition The standard temp is 20deg Celsius and the site temp is…

A: Given data: correction for temperature Ctemp =0.02 m correction for pull Cp =-0.01 m

Q: A line was measured using a tape that is suspended with a pull of 145 N on both ends. The mean…

A: Determine the correction due to sag?

Q: use the virtual work method to determine the deflection at point C of the beam shown

A: Given :- A beam is shown with two point load of 200 kN and 100 kN Modulus of elasticity constant (E)…

Q: . . . From the following measured angles, calculate the adjusted angles according to the weight of…

A:

Q: A civil engineer used a 30m tape in measuring an inclined distance. The measured length on the slope…

A: Given :- Length of the tape = 30 m Measured length of the slope = 459.20 m  Difference between…

Q: 3. A line was found to be 2,850 m long when measured with a 50-m tape under a steady pull of 5.5 kg.…

A:

Q: A line was measured using a tape that is suspended with a pull of 145 N on both ends. The mean…

A:

Q: In the two peg test of a dumpy level, the following observations are taken Instrument at AInstrument…

A: Given: The observations for two peg tests are,   Instrument at A Instrument at B Rod…

Q: A line was measured using a tape that is suspended with a pull of 145 N on both ends. The mean…

A: Correction due to pull is given as Cp = (Pm - Po)L/(AE)

Q: A line was recorded as 2350.00 meters long. The standard tape weighs 0.65 kg, 30.00m long at 20°C…

A: Given:E=200 GPaA=2.50 mm2Gradient=3%Coefficient of linear expansionα=0.0000116 m/°CStandard tape…

Q: A student used a 30m tape in measuring inclined distance. The measured length on the slope was…

A: Note: Hi! Thank you for the question, as per the honor code, we are allowed to answer three…

Q: Determine the correcthorizontal distanceAEwhen it was measured AB = 45m, BC= 38m, CD= 55m, DE…

A:

Q: 8. RISE AND FALL MRTHOD. Using the rise and fall method, complete the level notes given below and…

A: We will tabulate the table and then apply arithmetic check.

Q: 3. The following observations were made during the testing of a Dumpy level. Instrument at Staff…

A:

Q: 3. A student used a 30m tape in measuring inclined distance. The measured length on the slope was…

A:

Q: Engineer used SUP tape in asuring an Clined distance. The measured length on the slope was recorded…

A: Tm=35T0=28PS=12P0=8A=0.03cm2=3mm2E=200×103 N/mm2 (assumed as not given in question)

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.