A line was measured using a tape that is suspended with a pull of 145 N on both ends. The mean temperature during the measurement was 14°C. The whole length of the line was measured with 4 consecutive spans/segments. The tape was supported only at the ends of each segment when the measurement was done. The measured segments of the line are as follows: 29.988 m, 29.895 m, 29.838 m, and 29.910 m. Therefore the total length of the line measured was 119.631m. The tape was standardized with the following parameters: Standard pull = 95 N Standard temperature = 14°C Cross-sectional area = 3.35 mm^2 weight per length of the tape = 0.24525 N/m Coefficient of linear expansion = 0.9 x 10^-6 per °C Young's modulus = 14.8 x 10^4 MPa %3D

A line was measured using a tape that is suspended with a pull of 145 N on both ends. The mean temperature during the measurement was 14°C. The whole length of the line was measured with 4 consecutive spans/segments. The tape was supported only at the ends of each segment when the measurement was done. The measured segments of the line are as follows: 29.988 m, 29.895 m, 29.838 m, and 29.910 m. Therefore the total length of the line measured was 119.631m. The tape was standardized with the following parameters: Standard pull = 95 N Standard temperature = 14°C Cross-sectional area = 3.35 mm^2 weight per length of the tape = 0.24525 N/m Coefficient of linear expansion = 0.9 x 10^-6 per °C Young's modulus = 14.8 x 10^4 MPa %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use slope deflection method. Solve for all the support reactions. Indicate units & directions.
Draw the moment diagram using the force method
PART 2. PROBLEM SOLVIN B 4. ORAW THE SHEAR AND MOMENT DIAGRAM. 3500 1b 500 1b ft 3ft →と eft 3ft
Determine the vertical displacement at A for the structure below by using virtual work and FMoA. Please treat the internal moment at C as the redundant force. (E, I = Constants; A = ∞) A P wit 40-50 L 3 L 2 L 2 B
Analyze by force method. Draw the axial , shear , moment diagrams δA= 12/EI δD= 3/EI
Determine the reaction experience at hinge B along y-axis because of that applied force P. The tension in the rod is T= 0.5 MN.
Question 3 of 10 View Policies Current Attempt in Progress Answers: MB = MA= The 43-N force P is applied perpendicular to the portion BC of the bent bar. Determine the moment of P about point B and about point A. Moments are positive if counterclockwise, negative if clockwise. i i P = 43 N < 1.3 m B 41° 1.3 m N.m N.m ■ -12 C E
2. Draw the moment diagram. Assume joint B is a roller. By using slope deflection method. El is constant. 35 kN 25Nm 4m 3m 4 m
Using Virtual Work Method, calculate the horizontal displacement at joint B for the truss loaded as shown. The areas in mm2 are shown in parenthesis. E = 200 GPa for all members. В 200 KN (5000) (5000) (5000) D A. -(3500) Е (3500) 3 m 3 m (000s) (00SE)
10. Will upvote to anyone who will answer. Correct units pls. Thanks