Answered: Determine the contact force between the…

Determine the contact force between the smooth 90-kg ball 8 and the horizontal bar, and the magnitude of the pin reaction at A. Neglect the weights of the bar and the pulley.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.85P: Determine the contact force between the smooth 90-kg ball B and the horizontal bar, and the...

See similar textbooks

Related questions

Q: Gravity is given by g – 9.81 – 3.32 x 10 *h m/s³, where h is the height above sea level. An airplane…

Q: The particle P starts from rest at point A at time t = 0 and changes its speed thereafter at a…

A: Find the acceleration and angle at given time .

Q: Consider the following fluids at a film temperature of 300 Kin parallel flow over a flat plate with…

Q: Using the method of composite figures, determine the location (coordinate) of the centroid of the…

Q: A glass capillary tube of diameter 0.3 mm and length 60 mm is dipped in a water having surface…

A: Given datadiameter of capillary tube = d = 0.3 mm = 0.3 x 10-3 mLength of capillary tube = L= 60 mm…

Q: A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81 inches as…

Q: 2. Determine the slope and maximum deflection at C of the beam shown in Figure Q2. Figure Q2 с M B

Q: A prototype engine was built and tested, during the non-flow process it is observed that the Work…

Q: The initial volume of air is 100L in a cylinder fitted with a piston at a pressure of 150 kPa and a…

Q: The circus manager doesn't believe your equations. He draws a diagram showing some possible…

A: The circus manager appears to be dubious about the requirement for a set speed for the acrobat and…

Q: 5. Calculate the reactions at the built-in support at C, neglecting the weights of the members. so0…

Q: 1. A pressure gauge attached to a pipe is reading 1.34 m of Hg at a place where the atmospheric…

A: a) Pgau=1.35 m of Hg Patm=10.33 m of H2O…

Q: Determine ly and ky.

Q: 1. An S0 kg container box is resting on a wooden support as shown in the figure. The coefficient of…

A: For solution refer below images.

Q: 1. Problem Solving. Woite inside a Box. 1) Find the alliwable safe load p if the stresser in the bar…

A: Stress in bar AB, σAB=60ksi=413.685N/mm2Stress in bar BC, σBC=50ksi=344.738N/mm2Stress in bar CD,…

Q: 3. Pelton wheel runner produces 20 MW under a head of 450 m when running at a speed of 600 rpm. If…

Q: What are the pressures at the A(conjunction of water and oil), B (middle of water), C (bottom of the…

Q: 2. The uniform rod in the figure shown weighs 400N and has its center of gravity at G. Determine the…

A: To determine the tension in the cable T and the normal reactions at Point A and B.

Q: A mass m of helium gas is in a container of constant volume V. It is initially at pressure P and…

A: Given:- initial condition, m1 = m Pressure, P1 = P Temperature, T1= T And final condition as, mass,…

Q: Use the phase diagram for carbon (shown at right) to describe the phase changes that a sample of…

Q: :) Select the lightest W-shape standard steel beam equivalent to the built-up steel beam below which…

A: we have to select the appropriate section for the given moment

Q: 1) Select the lightest W-shaped section that can safely support the load. The beam is made of steel…

Q: Water flows from the nozzle attached to the spray tank shown in the figure below. Determine the…

Q: being stretched it occupies the interval 0<A<lo. Also, before being stretched, for OSA< A0, the…

A: the boundery conditions are limA→A0- UL(A)=limA→A0+UR(A)UL and UR are the displacement and stress…

Q: For the given composite cross-sectional area in Figure 1, determine the location (x, y) of the…

Q: 2. water surface -2.5m 1.5mradius The corner of a floating body has a quarter cylinder AB having a…

Q: 7. Determine completely the resultant of copianar concurrent force system shown in the figure. 500N…

Q: The cantilever beam is built into a wall at 0. Neglecting the weight of the beam, determine the…

Q: The pulley-cable system supports the 150-lb weight. The weights of the pulleys and the horizontal…

Q: Determine the magnitudes of the pin reactions at A and C. Neglect the weights of the members. 800 NI

Q: 2) If the bearing pads at A and B support only vertical forces, determine the greatest magnitude of…

Q: Question 5 A ball shooter uses air pressure to propel a 0.9 kg ball in a smooth tube angled at 22°.…

Q: Prob. # 5] A spring-mass system, k, and m, has a natural frequency f1. If a second spring k2 is…

A: To find: The value of k2 in terms of k1. Given: The initial frequency is f1. The final frequency is…

Q: Thex-and y-motions of guides A and B with right-angle slots control the curvilinear motion of the…

A: given; x=18+0.67t2y=18-0.61t3x and y in mm.velocity at t=3s

Q: The 4 kg box shown in the figure start from rest at t = 0 in which the friction is negligible.…

A: Givent=0t=1sm=4kgF=9.81N

Q: A 30 kW cooler machine runs at a speed of 4000 RPM One of the bearings is suspected with severe…

A: A's per the guidelines, we are allowed to solve only the first 3 subparts of this question. You may…

Question

Answer with complete and detailed solution

Determine the contact force between the smooth 90-kg ball 8 and the horizontal bar, and the magnitude of the
pin reaction at A. Neglect the weights of the bar and the pulley.
21m
-b.6 m-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

The 1200-lb homogeneous block is placed on rollers and pushed up the 10 incline at constant speed. Determine the force P and the roller reactions at A and B.
Determine the contact force between the smooth 90-kg ball B and the horizontal bar, and the magnitude of the pin reaction at A. Neglect the weights of the bar and the pulley.
The two uniform cylinders, each of weight W, are resting against inclined surfaces. Neglecting friction, draw the free-body diagrams for each cylinder and for the two cylinders together. Count the total number of unknowns and the total number of independent equilibrium equations.
The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
The 180-lb homogeneous bar is supported by a ball-and-socket joint at A and two cables attached to B. Determine the forces in the cables.
The four-bar linkage supports the homogeneous box of weight W. Neglecting the weight of the linkage, determine the horizontal pin reactions at A and B.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
The 60-lb homogeneous door is supported by hinges at A and B, with only the hinge at B being capable of providing axial thrust. The cable CD prevents the door from fully opening when it is pulled by the 40-lb force acting perpendicular to the door. Draw the FBD for the door, and count the unknowns.
The three bars are welded together to form a rigid unit that is supported by three slider bearings. Neglecting the weights of the bars, determine the magnitudes of the three bearing reactions caused by the 120-lbin. couple.
The 40-kg homogeneous disk is resting on an inclined friction surface. (a) Compute the magnitude of the horizontal force P. (b) Could the disk be in equilibrium if the inclined surface were frictionless?
The uniform, 20-kg bar is placed between two vertical surfaces. Assuming sufficient friction at A to support the bar, find the magnitudes of the reactions at A and B.