Determine the compressive load that can be carried by a UC 305 x 305 x 158 in S275 steel over a height of 3m, assuming that it is braced against the weak-axis failure and that the maximum moment about its major axis is 50 kNm. (Calculate the cross-section strength only.)

Determine the compressive load that can be carried by a UC 305 x 305 x 158 in S275 steel over a height of 3m, assuming that it is braced against the weak-axis failure and that the maximum moment about its major axis is 50 kNm. (Calculate the cross-section strength only.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A WT305 × 41 standard steel shape is used to support the loads shown. Assume w = 50 kN/m, LAB = 1.4 m, LBC = 2.8 m, and LCD = 1.4 m. Consider the entire 5.6 m length of the beam and determine:(a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and(b) the maximum compressive bending stress at any location along the beam (enter a negative answer).
The tee section shown below is to carry a bending moment of 8440 N·m. It is to be made of steel plates welded together. If the load on the beam is a static load, would SAE 1020 hot-rolled steel be satisfactory for the plates? -175 mm 25 mm 200 mm 25 mm
A simply supported beam with span of 6.5 m is subjected to a counterclockwise moment at the left support and a clockwise moment at the right equal to 30% of the moment at the left support, both acting in the plane of the minor axis of the beam. The beam is not restrained against lateral buckling. The beam is A36 steel with yield strength Fy = 248 MPa. Properties for this problem are: rT = 0.053 m d = 0.60 m bf = 0.200 m tf = 0.015 m S = 0.00211 m3 Determine the allowable flexural stress in the compression flange, in MPa. Determine the maximum value of the moment at the left support, in kN-m.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 18 kips, w = 5.6 kips/ft, LAB = 5.0 ft, LBC = 5.0 ft, and LCD = 13.6 ft. Determine the magnitude of the maximum bending stress in the beam. LAB LBC LCD Answer: i ksi Omax
14.4 Identify the type of masonry block shown below
AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 56 kN/m, LAB = 1.0 m, LBc = 2.0 m, and LCD = 1.0 m. Consider the entire 4.0 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). y LAB LBC LCD WT305 x 41 Answer: (a) OmaxT= MPa (b) Ơmax.C = MPa
Plastic stage is when all elements of a steel section is in yielding condition and reaches its utlimate strength before it collapses without lateral torsional buckling. O True O False
AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
SOLVE please Determine the design bending strength of ISLB 350 @ 486 N/m, considering the beam to be laterally supported. Assume factored design shear force will not exceed 0.6 times the design shear strength of the cross-section. If it is used as simply support beam of unsupported length 5 m then determine the factored distributed load the beam can carry. Use Fe410 grade steel For ISLB 350 @ 486 N/m, section properties are as follows: h = 350 mm; b= 165 mm; t₁ = 11.4 mm; t = 7.4 mm; R₁ = 16 mm; Izz = 13158.3 × 104 mm²; I = 631.9 × 10¹ mm²; Zpz = 851.11 × 10³ mm³; Zez = 751.9 x 10³ mm³
Figure 1 shows the cross-section of a heavily welded I-section steel column under axial compression. The yield stress of the steel section is 300 MPa. (a) Check the slenderness of the flanges and webs. (b) Determine the effective and gross areas of the cross-section. (c) Determine the design axial capacity of the cross-section. 380 E 10 425 -8 Figure 1. Cross-section of the rectangular hollow section steel column (Units: mm)
I need the answer as soon as possible