Determine the amplification factor for the following braced column (W21x44) (A992 steel). The flexural rigidity, El, is unreduced, Use ASD. ML= 22 ft-k MD= 19 ft-k 20 W21x44 ML= 29 ft-k MD= 33 ft-k PL= 100 k PD= 220 k

Determine the amplification factor for the following braced column (W21x44) (A992 steel). The flexural rigidity, El, is unreduced, Use ASD. ML= 22 ft-k MD= 19 ft-k 20 W21x44 ML= 29 ft-k MD= 33 ft-k PL= 100 k PD= 220 k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Select an A992 steel for the following beams. Use Cb = 1.0 for your calculations. Check for Shear.…

A: Given data: PL=250 lbwD=17.5 kip/ftFy=50 ksi To design the given beam, AISC code provisions can be…

Q: The span length of the T-beams shown in the following figure is 28 ft. 38" 8#10 fe= 3 ksi f, = 75…

A: The given data is: Span of length, L=28 ft =28*12…

Q: The cantilever beam shown in figure 3 is a W18x55 of A992 steel. Lateral bracing is supplied at the…

A: A cantilever beam is a structural component with one end protruding beyond the point of support and…

Q: Determine the effective length factor for column MN of the unbraced frame shown. The loads applied…

A: Column section MN = W12x96 Beam section = W18x46 Column length, L = 13 ft Beam length = 30 ft Dead…

Q: 8. HSS 10 x 8 x1/4 with Fy-50 ksi is selected to be used as a compression member with KL=10ft.…

A: Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: For what reason must wires and plumbing fixtures installed above drop ceilings be plenum-rated?

A: Cables are distinguished as plenum and non-plenum based on the outer covering's (jacket) fire…

Q: A simply supported beam with a span length of 48 feet is laterally supported at its ends and is…

A: Span of simply supported beam = 45 ftDead load = 400 lb/ftLive load = 1000 lb/ftSection of the beam…

Q: Select the lightest W14, 15 ft long, beam-column that is not subjected to sidesway. The service…

A: Use the LRFD design method.

Q: Determine the available compressive strength (p.P) of a composite column with the length of 25 t.…

A: Available compressive strength of the column= PN= Ac(0.85 fc')+Asfy fc'=5000 psi Ac=…

Q: Situation 20. A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is…

A: Given, Ag = 14,968 mm2 rx = 133.65 mm ry = 77.47 mm

Q: 2. Determine the applicable value of Pu for the following braced frame. The beam is a W10x45…

Q: Select the lightest rolled shape W section steel beam for a member with a simply- supported span of…

A: Dead load and live load is given. We need to find out W section

Q: se Allowable Strength Design. Use A992 steel and select a W-shape for the following beam: •…

A: Given- Service dead load = 0.4 kips/ftService live load = 1.2 kips/ftdead load=10kiplive load=12…

Q: Check the beam shown for compliance with the AISCS. Lateral support is provided only at the ends,…

A: Load=70 Sin =70*(4/5) =56 KN =12.58 kipsDead Load=30% of 12.58=3.78 kipsLive…

Q: The section shown below is made of 50 ksi A992 steel. The x-axis is lateral and the y-axis is…

A: Given: The yield stress of the steel is 50 ksi. Consider the figure,

Q: square base plate is inn

Q: Q: Design the member AB within the frame shown. The applied load is a service load. Use Fy-50 ksi. k…

A: Axial compression member Service load= 300 kipLength of compression member = 15 ft.Steel Section =…

Q: The properties of the steel column are shown in the table. Yield strength of the column and base…

Q: For the composite shaft shown, the total twisting angle is the sum of the twisting angles of steel…

A: False The shafts are bonded together as a composite bar so they will have strain compatibility. As…

Q: ISC Equation E3-2 or E3-3. Use Actual recommended fixity factor k=0.8. HINT: SERVICE LOAD IS (DL+LL)…

Q: 5m 3m 3m 3m 3m Solve for the safest factored load Pu the compression members AB and BC can carry in…

A: For W16x50 Area = 14.7 sq-inch Assuming A992 steel So, yield strength (fy) = 50 ksi So, Tmax =…

Q: 2. Determine whether the compression member shown in the figure below is adequate to support the…

Q: A W14 x 74 compression member carries a service loads of DL= 2,500 KN and LL= 300 KN. The column is…

A: It is required to determine the factored load using ASD method. Pu=DL+LL=2500 kN+300 kN=2800 kN The…

Q: Verify the adequacy of column BC, part of a sway frame structure, to carry the loads shown in the…

Q: A W section of A992 steel (E350 MPa and F₁= 450 MPa) is used to serve as a column 4.90 m long to…

A: Hi! Thank you for the question As per the honor code we are allowed to do only one question at a…

Q: Q2. Design the required tensile and compression rebars for the cross section shown below. Mu= 288…

A: for given cross section given b=250mm D=500mm MU=288KN-M FC=20 MPA FY=300MPA

Q: 16 ft 8 ft 8 ft 一年 JU Deal-column member The memer is A992 steel (Fy=50 ks member is laterally…

A: Given, W12×58 LX=LY=16 ft yield strength Fy=50 ksi Allowable stress bending coefficient cb=1 kx=ky=1…

Q: A WT305 x41 standard steel shape is used to support the loads shown. Assume W= 50 kN/m, LAB = 1.1 m.…

A: To Determine Maximum Compressive and tensile stress.

Q: Explain What factors determine the requirements for traffic control and safety hardware management…

A: The requirements for traffic control and safety hardware management data collection survey…

Q: 3.3. Determine the maximum service live load that the column can support if the live load is twice…

A: Section C8×18.75 Calculate the moment of inertia about y-axis…

Q: design flexural strength.

Q: Situation 3. A W12x81 is used as a column. The effective length in either principal direction is…

A: The question asks you to find the cutback width (labeled as 2.187) based on the given information.…

Q: A W21 x 68 of A992 steel is used as a simply supported beam with a span length of 50 feet. The only…

A: For section ,

Q: Determine the amplification factor for the following braced column (W21x44) (A992 steel). The…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: A WT205 × 30 structural steel section (see Appendix B for cross-sectional properties) is used for a…

A: To Find a. Slenderness ratio b. Euler buckling load c. Axial stress in column Given data WT205×30…

Q: 3. Design a column of wide flange section W for the member (DE) of the frame shown below The frame…

A: Given data: Axial load on the column, P=2500 kN Effective length factor, Ky=1.0 and Kx=2 The column…

Q: A compression member is built up from a W14x90 and a W10x49, both of A992 steel. a. Compute rx and…

A: We need to first obtain the Moment of inertia about X and Y axis We can determine the moment of…

Q: Calculate the development length at simply supported edge in mm from the following information: M25…

A: Given- M25 and Fe 415 steel bd =1.4 MPa V = 30 KN and M = 16.076 KN-m Side way clear spacing is 50…

Q: The rigid frame shown is unbraced. The members are oriented so that bending is about the strong…

A: Given- Axial strength of column AB=?

Q: AW14 x 53 of Grade 70 steel is used as a compression member. It is 30 feet long, pinned at the top…

Q: The rigid frame shown is unbraced. The members are oriented so that bending is about the strong…

A: Answer We need to first find G factors at Joint A and joint B in order to calculate 'Kx' GA = 1…

Q: The given frame is unbraced, and bending is about the x axis of each member. The axial dead load…

A: Given:- The frame is unbraced The bending is about the x axis of each member The axial dead load on…

Q: A simply supported beam with a span length of 48 feet is laterally supported at its ends and s…

A: Span of simply supported beam = 45 ftDead load = 400 lb/ftLive load = 1000 lb/ftSection of the beam…

Question

Determine the amplification factor for the following braced column (W21x44) (A992
steel). The flexural rigidity, El, is unreduced, Use ASD.
ML= 22 ft-k
MD= 19 ft-k
20
W21x44
ML= 29 ft-k
MD= 33 ft-k
PL= 100 k
PD= 220 k

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Calculation

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 6 of 6 Fill in the blanks: Determine the design moment capacity of the beam with given properties below. bf = 400mm bw = 350mm tf = 120mm d = 370mm d' = 100mm fc' 34.5 MPa fy = 420 MPa As = 8- 28mm bars USE NSCP 2015, Mu = KN-m
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee
A W14 x 74 compression member carries a service loads of DL= 2,500 KN and LL= 300 KN. The column is fixed at the top end and pinned at the bottom. The length is 6 m. If A992 steel (Ex= 350 MPa and F₁- 450 MPa) is used, check the adequacy of the column. Check also the column stability. Use ASD.
W 14 x 142 is used as a column having a length of 9 m. long. It is hinged at the r end and fixed at the lower end but there is a lateral bracing perpendicular to minor axis of the W section at a point 6 m. above the bottom support. It is assumed to be pinned connected at the bracing point. Using A 36 steel Fy 248 MPa the NSCP Specifications. E= 200000 MPa. Properties of W 14 x 142 A-26967.69 mm2 d=374.65 mm bf=393.70 mm tf-27.00 mm tw 17.27 mm Ix 695.11 x 106 mm4 Iy = 274.71 x 106 mm4 rx = 160.53 mm ry 100.84 mm 221 Assume: Kx=0.80 for 9 m. length KY 1.9 for the length on the upper support KY-0.80 for the length on the bottom support CIVIL ENGINEERING- STEEL DENON a) Compute the slenderness ratio along y-axis. b) Compute the slenderness ratio along x-axis. c) Compute the safe axial load
2. Determine the lightest W-shape for a column 30' tall in a braced frame. The column is braced at mid-height in the weak direction. The loads are 100k dead load and 200k live load. The bottom of the column is pinned and the top of the column is constrained in rotation.* Use A572 Grade 60 steel. *Not tronslation.
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
Analysis of frames/Zero force identification please show complete solution
3-3 A rectangular section with width b=200mm and depth h=450mm is reinforced with 4 16 of HRB400, The design bending moment is M=100KN •m. Is the section safe or not? F00
answer should be on the choices
Please Determine the axial load strength and moment (without and with reduction factor) a square columns for the following conditions and draw their interaction diagrams (note the scale): When conditions are in balance During the tensile condition When the pressure condition Pure axial Pure moment
Determine the design strength and the allowable strength for the compression member shown. Use NSCP 2015 and a steel with Fy =50ksi. L3X2.5X1/4 kL = 8ft PL 3/8 X 8 L3X2.5X1/4
steel structure (AISC ) masnual