Select the lightest rolled shape W section steel beam for a member with a simply- supported span of 16 ft. The beam must support a uniformly distributed load of D= 2.1 k/ft and L= 4.5 k/ft. Lateral support of the compression flange is provided at the ends and the centerline of the beam span. Determine a value of Cb. Neglect the beam self-weight and use A992, Grade 50 steel. As part of your answer indicate the following: Member selected W_x Cb = OMn Mu

Select the lightest rolled shape W section steel beam for a member with a simply- supported span of 16 ft. The beam must support a uniformly distributed load of D= 2.1 k/ft and L= 4.5 k/ft. Lateral support of the compression flange is provided at the ends and the centerline of the beam span. Determine a value of Cb. Neglect the beam self-weight and use A992, Grade 50 steel. As part of your answer indicate the following: Member selected W_x Cb = OMn Mu

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer correctly. Please I need this ASAP. thank you Note: The tolerance is ± 1 in the third significant digit
Determine the design strength of a T-Beam with the following data: b+= 700 mm bw = 300 mm hy = 100 mm d = 500 mm f₂ = 21 MPa fy = 414 MPa A: 5-20 mm dia.
A W12 × 58, L= 24 feet long, is pinned at both ends and braced in the weak direction, as shown in 1 Figure. A992 steel is used. Determine the available compressive strength L/4 A L/4
A simply supported beam with span of 6.5 m is subjected to a counterclockwise moment at the left support and a clockwise moment at the right equal to 30% of the moment at the left support, both acting in the plane of the minor axis of the beam. The beam is not restrained against lateral buckling. The beam is A36 steel with yield strength Fy = 248 MPa. Properties for this problem are: rT = 0.053 m d = 0.60 m bf = 0.200 m tf = 0.015 m S = 0.00211 m3 Determine the allowable flexural stress in the compression flange, in MPa. Determine the maximum value of the moment at the left support, in kN-m.
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee
An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). a. Check for compactness of the given section? b. In checking section's compactness, calculate the upper limit for compact flange category? c. In checking section's compactness, calculate the upper limit for non-compact web category?
AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
2. Determine the lightest W-shape for a column 30' tall in a braced frame. The column is braced at mid-height in the weak direction. The loads are 100k dead load and 200k live load. The bottom of the column is pinned and the top of the column is constrained in rotation.* Use A572 Grade 60 steel. *Not tronslation.
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN
i need the answer quickly
Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19 mm bolts in each flange. Hole diameter is assumed to be three mm more than the bolt diameter. Neglect the weight of the section. a.What is the capacity of member CG? b. Design member CG using a W section. c. What is the tensile capacity of the section for CG based on gross area? The following W Section were considered for the design: W10x33 W14x38 W8x40 W16x36 W10x39 W8x13 189 KN 1.50 HL B 145 KN 1.50 E + 137 KN 121 KN -3.00 + 12.00 3.00 154 KN + W4x13 W6x9 W10x12 200 KN -1.50 1.50 1 030 T 1.20 +2.40 0.60 L i 0.30
plss, i need the answer immediately!