Sound Tek Inc. manufactures electronic stereo equipment. The manufacturing process includes printed circuit (PC)board assembly, final assembly, testing, and shipping. In the PC board assembly operation, a number of individualsare responsible for assembling electronic components into printed circuit boards. Each operator is responsible forsoldering components according to a given set of instructions. Operators work on batches of 50 printed circuit boards.Each board requires 4 minutes of board assembly time. After each batch is completed, the operator moves theassembled boards to the final assembly area. This move takes 9 minutes to complete.The final assembly for each stereo unit requires 18 minutes and is also done in batches of 50 units. A batch of 50stereos is moved into the test building, which is across the street. The move takes 20 minutes. Before conducting thetest, the test equipment must be set up for the particular stereo model. The test setup requires 30 minutes. The unitswait while the setup is performed. In the final test, the 50-unit batch is tested one at a time. Each test requires 8minutes. The completed batch, after all testing, is sent to shipping for packaging and final shipment to customers. Acomplete batch of 50 units is sent from testing to shipping. The Shipping Department is located next to testing. Thus,there is no move time between these two operations. Packaging and labeling requires 9 minutes per unit.1. Determine the amount of value-added and non-value-added lead time and the value-added ratio in this processfor an average stereo unit in a batch of 50 units. Categorize the non-value-added time into wait and move time.Round the percentage to one decimal place.x min.Value-added lead timeNon-value-added lead time:Wait time lead timemin.Move time lead timemin.Total non-value-added lead timemin.Total lead timemin.Value-added ratio (as a percent)

In the PC board assembly operation, assembling electronic components into printed circuit boards. As…

Determine the amount of value-added and non-value-added lead time and the value-added ratio in this process an average stereo unit in a batch of 50 units. Categorize the non-value-added time into wait and move time. nd the percentage to one decimal place. x min. ue-added lead time 7-value-added lead time: Wait time lead time min. Move time lead time min. al non-value-added lead time min. al lead time min. ue-added ratio (as a percent)

Determine the amount of value-added and non-value-added lead time and the value-added ratio in this process an average stereo unit in a batch of 50 units. Categorize the non-value-added time into wait and move time. nd the percentage to one decimal place. x min. ue-added lead time 7-value-added lead time: Wait time lead time min. Move time lead time min. al non-value-added lead time min. al lead time min. ue-added ratio (as a percent)

FINANCIAL ACCOUNTING

10th Edition

ISBN:9781259964947

Author:Libby

Publisher:Libby

Chapter1: Financial Statements And Business Decisions

Section: Chapter Questions

Problem 1Q

See similar textbooks

Similar questions

Prepare a cost of quality report. Round the percents of total quality cost to the nearest whole number and the percents of total sales to one decimal place. Cost of Quality Report Percent of Total Quality Quality Cost Classification Quality Cost Percent of Total Sales Cost Prevention Appraisal Internal failure External failure Total % 1.1.0.0.0 % % % % %
Do not give answer in image
Please do not give solution in image format thanku
C (Ib/gal) - 5.8. A mixing process may be described as follows: A stream with solute concentration Ci (pounds/volume) is fed to a perfectly stirred tank at a constant flow rate of q (volume/time). The perfectly mixed product is withdrawn from the tank, also at the flow rate q at the same concentration as the material in the tank Co. The total volume of solution in the tank is constant at V. Density may be considered to be inde- 2.1 2.0 1.9 1.8 1.7 W FIGURE P5-8 10 6:30 A.M. Time 6:52 A.M. pendent of concentration. A trace of the tank concentration versus time appears as shown in Fig. P5-8. (a) Plot on this same figure your best guess of the quantitative behavior of the inlet concentration versus time. Be sure to label the graph with quantitative infor- mation regarding times and magnitudes and any other data that will demonstrate your understanding of the situation. (b) Write an equation for C; as a function of time. Data: tank dimensions: 8 ft high by 5-ft diameter Tank volume V: 700…
Devsi
RI 6.7.8-Q-InsertYourLastName E Share KEE Insert v V A eral Delete v 个八Z Analyz- Data Conditional Format Cell Sort & Find & Formatting as Table Styles Format v Filter Select 0 00 |6 % K M. 7. Job-Order Costing Problem Using the weighted procedure method of setting rates, calculate the relative value and cost per procedure $1,250,000 and an average hourly lab tech rate of 0.25 ) for the following lab procedures, given a total lab cost of $15 (to calculate the RVU, divide the total sample expense by Sample Labor In Hours Labor Sample Labor Sample Supply In Minutes Projected Procedure Volume Expense ($) Expense ($) Amylase 15 0.75 000 12 Bleeding Time 0.50 000'sS 0.50 000' 7,800 Uric Acid Platelet Count 0.25 6. Hematocit 0.25 8.
Please help me with b2, c1, and c2. Thanks!
As you watch the simulation, please keep in mind that this is a scenario where the system flow rate is R = 9 passengers per minute and the flow time is T = 6 seconds. Question 1: Use Little’s Law to compute the average inventory in this system, measured in “passengers. Question 2: On the basis of this information, would you expect the average inventory to increase or decrease from your answer to question 1? Why? Explain briefly in words. Question 3: Now use Little’s Law to compute the correct inventory when R = 10 passengers per minute. State the new inventory, I. Were you correct in question 2?
Godo
Tableau DA 16-1: Quick Study, Computing equivalent units LO P1 Monsta Cola hires us to help assign and report costs. The company has two departments: mixing and bottling. To aid our analysis, the following Tableau Dashboard is provided with information for the mixing department. The company uses the weighted average method. Work in Process Inventory (In Units) 190000 Beginning inventory Units started this period 640000 Units completed and transferred Ending inventory 200000 100,000 200,000 300,000 400,000 500,000 600,000 700,000 800,0 Work in Process Inventory Percent Complete Beginning Ending 10... 80% 70%. 60%. 60% 神 40%. 40% 20% 30% 0% Direct Materials Conversion Direct Materials Conversion Work in Process Inventory Costs Beginning Inventory Costs Inventory Costs Added During 142500 Conversion konversion Conversion Costs, Added: $1,810,000 390000 Direct Materials Direct Materials 2460000 * + ableau 1. Compute the number of units completed and transferred out. 2. Compute the total…
Crex Co was set up by Cynthia Rex who created her own brand of chalk paint 20 years ago. Using her background in fine art, she developed this specialist chalk paint to be used in the restoration of furniture and to decorate accessories. The chalk paints are exclusively available through Crex Co's network of over 800 independent stockists who are located in over 30 countries around the world. The manufacturing process begins with the three chemicals required for the paint being measured on electronic scales. A worker then takes the chemicals and places them into a machine for mixing. Once mixed the worker removes the mixture from the machine and transfers it to tin containers. The standard material costs per litre of chalk paint are as follows: Litres required $ per litre 0.80 1.20 0.15 1.40 0.10 0.80 1.05 Material Latex paint Plaster of Paris Calcium carbonate At the end of the last period, actual output of the chalk paint was 3,325 litres and actual data relating to this production…
I need typing clear urjent no chatgpt use i will give 5 upvotes