Determine the allowable (ASD) tensile strength (kN) of the angle shown. It is welded on the end (transverse) and sides (longitudinal) of the long leg only. The yield strength is 248 MPa while the ultimate tensile strength is 400 MPa. Neglect block shear strength. The angle is L203X152X19. Plate weld Angle 203 Section view Plate - Plan view 150

Determine the allowable (ASD) tensile strength (kN) of the angle shown. It is welded on the end (transverse) and sides (longitudinal) of the long leg only. The yield strength is 248 MPa while the ultimate tensile strength is 400 MPa. Neglect block shear strength. The angle is L203X152X19. Plate weld Angle 203 Section view Plate - Plan view 150

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the tension member shown, compute the following. a. The tensile design strength. b. The allowable tensile strength. Weld PL 14 x 6 A36 steel
A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).
20. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksit) what is the weld capacity perpedicular to the beam of the flange connection in kips? (2 decimal places)
| * A's O As,web As bw Steel areas: A's-2 + 14 = 308 mm² A₁=50 mm² (area of $8) Materials : C25/30 / B420C Longitudinal reinforcements A's=2 $ 14 As,web= 2 $ 12 As= 5 0 14 bw=300 mm d=670 mm d'=30 mm k₁= 0,85 k3 = 0,85 Pb=0.0205 (from table) Transverse Reinforcements $8/200 mm (2-leg stirrups) Material coefficients Ymc:1.5 (Concrete) Yms: 1,15 (Steel) Determine the reinforcement ratio and failure type of the beam As,web= 212= 226 mm² Asw=2x50=100 mm² (Total Area of two leg stirrup) A₁= 5 + 14=770 mm²
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
Please help me with my homework and use ASEP STEEL HANDBOOK 2004 volume 1 Dimensions and Properties Third Edition, to find the AISC. PLEASE SHOW COMPLETE SOLUTIONS AND DETAILS.
Please correct answer otherwise dislike
7. Determine the design tensile strength of the plate (200 x 10 mm) connected to 12 mm thick gusset, using 24 mm bolts as shown below. Use A572M Grade 345 steel materials. 200 40 50 40 30 30 30 30 40
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 2L5 x 3 x16 LLBB Determine the allowable tensile strength for ASD. Select one: а. 52.1 b. 104.2 c. 87.8 d. 43.9
Determine the load capacity of the angle LRFD. USE NSCP 2015.