Determine: 1. The basin dimensions. 2. The power required. 3. The impeller diameter if a vane-disc impeller with six flat blades is employed and the tank has four vertical baffles (one on each tank wall). The impeller diameter is to be 30 to 50% of the tank width. 4. The impeller diameter if no vertical baffles are used. 5. The air required if pneumatic mixing is employed and the diffusers are 0.15 m above the tank bottom.

Determine: 1. The basin dimensions. 2. The power required. 3. The impeller diameter if a vane-disc impeller with six flat blades is employed and the tank has four vertical baffles (one on each tank wall). The impeller diameter is to be 30 to 50% of the tank width. 4. The impeller diameter if no vertical baffles are used. 5. The air required if pneumatic mixing is employed and the diffusers are 0.15 m above the tank bottom.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: If vacuum pressure at C equal to (Pc kPa) (Neglect Minor Losses). Determine X, Y, and pressure at D.…

Q: • Pump (or turbine) efficiency = Power Out / Power In • Schedule 40 steel and PVC pipe have the same…

A: a) Calculating the head pump delivery: hpump=∆Pγhpump=128 psi×114 in2ft262.4 lb/ft3hpump=295.38 ft

Q: A centrifugal fan is delivering 0.8 m/s of air at a total pressure differential (across the fan) of…

A: Given data Q=0.8 m3/sec=1695.10cfmArea=0.7 m2=0.753ft2pressure =350pa=1.40653 in-wgP=0.52 kW=0.697…

Q: The mechanical efficiency of the pump is 0.85 and pumping with a rate of 650 gal/min of engine oil…

Q: KAPLAN TURBINE RUNNER DEVELOPS 9300 KW UNDER A NET HEAD OF 7.4 M. MECHANICAL EFFICIENCY OF THE WHEEL…

Q: An absorption column is to be designed to recover 99.5% of the NH3 from a feed stream, which is…

A: Absorption: There are different methods of removing impurities or separating the chemicals.…

Q: Water (60°F) is running through Schedule-80 PVC pipe whose size changes gradually from 6-in nominal…

A: To solve this problem, we can use the Bernoulli equation, P + 1/2 * ρ * v² + ρ * g * z =…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

A square rapid-mixing basin, with a depth of water equal to 1.25 times the width, is to be designed
for a flow of 7570 m³/d. The velocity gradient is to be 790 mps/m, the detention time is 40 s. The
operating temperature is 10°C, and the turbine shaft is 100 rpm (µ = 0,00131 Ns/m² at 10°C, KL
= 65, KT= 5.75).
Determine:
1. The basin dimensions.
2. The power required.
3.
The impeller diameter if a vane-disc impeller with six flat blades is employed and
the tank has four vertical baffles (one on each tank wall). The impeller diameter is to
be 30 to 50% of the tank width.
4.
The impeller diameter if no vertical baffles are used.
5. The air required if pneumatic mixing is employed and the diffusers are 0.15 m above
the tank bottom.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:

VIEW

Step 2: 1. Calculation of basin dimensions:

VIEW

Step 3: 2. The Power required:

VIEW

Step 4: Calculations

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The water level in a wide tank is 20 m. the tank is open to the atmosphere. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up as shown in die ngure below. A pump is connected between the tank and the nozzle. If the maximum height of water column is 27 m above the ground, find the following neglecting the friction losses in the hose and fittings: a) The head of the pump in [m] b) The head of the pump in kPa Take the density of water as 1000 kg/m³ and the gravitational acceleration as 9.81 m/s? 27 m :20 m
Unless otherwise stated, take the density of water to be p.- 1000 kg/m and its specific weight to be Y.- 624 Ib/ft'. Also, assume all pressures are gage pressures unless stated otherwise. 2-9. The closed tank was completely filled with carbon tetrachloride when the valve at B was opened, slowły letting the carbon tetrachloride level drop as shown. If the valve is then closed and the space within A is a vacuum, determine the pressure in the liquid near valve B when h = 25 ft. The atmospheric pressure is 14.7 psi.
(3) Free jet 1 in. dia. 3 ft 10 psig 2 in. dia. to 1- For the figure above find Q?
3.4-2. Power for Agitation and Scale-Up. A turbine agitator having six flat blades and a disk has a diameter of 0.203 m and is used in a tank having a diameter of 0.61 m and height of 0.61 m. The width W = 0.0405 m. Four baffles are used having a width of 0.051 m. The turbine operates at 275 rpm in a liquid having a density of 909 kg/m³ and viscosity of 0.020 Pa -s. (a) Calculate the kW power of the turbine and kW/m³ of volume. (b) Scale up this system to a vessel having a volume of 100 times the original for the case of equal mass transfer rates. Ans. (a) P = 0.1508 kW, P/V = 0.845 kW/m', (b) P2 = 15.06 kW, P2/V2 = 0.845 kW/m³ %3D
shows a pump employed for lifting water from a sump. If its required to pump 60 liters/sec of water through a 0.1 m diameter pipe from the sump to point 10m above, determine the power required. Also determine pressure intensities at L and M. Assume efficiency of 70%. Pu-(YGYLD)
Q2. The pressure at a water main is 300 kPa gage. What size pipe is needed to carry water from themain at a rate of 0.025 m3/s to a factory that is 140 m from the main? Assume galvanized-steel pipe isto be used and that the pressure required at the factory is 60 kPa gage at a point 10 m above the mainconnection.
Prob-2 A hydraulic power system consists of a dam with an inlet connected to a turbine. H=15m, V₂-5m/s. Q=1m³/s. (hL is negligible); Point 1 and 2 open to atmosphere. V₁-0) Find: Power produced by turbine (kW). Last week Turbine As
Design a pipe to supply water from the elevated tank to the demand point at a discharge rate of 0.05 m3/s. Use Galvanized Iron pipe and assume water temperature as 15°C. Minor losses can be neglected due to smooth transitions.