Detemine the magilude of the sultant farce of the coplanar ferce system shawn in the ftng liqure belew where the helitental fice pa 13AN and the Couple m-590N NM SO 300mm 139 400 70

Q: 38 mm diameter AB shaft, Gakma = 250 MPa Made of a strong steel. Using the maximum shear stress…

A:

Q: For the following mechanism, Given: Lengths: O₂A=4 in, O3B=8 in, BC=5 in., O2O3-4 in. and offset…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 01 F1 A L/2 F2 02 B L/2 L = 3.00 m F1 = 12.0 N F2 = 16.0 N F3 = 20.0 N 01 = 70.00 02 = 25.00 03 =…

A: Given:L = 3 mF1 = 12 N, F2 = 16 N, F3 = 20 N70°, 25°, 10°Required:TB ( torque about the point B )

Q: I need help answering problems 11 and 12 pertaining to the print provided below.

A: 11.The threaded holes are represented as shown below figure.

Q: For the following mechanism, Given: • Lengths: O₂A-4 in, O3B=8 in, BC=5 in., O2O3-4 in. and offset…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: vino zmzinsdom уORGDEV-(aldslivs nouzoqmas Jem ed trum enoitibno gniwollol en mainsribem noizuhib en…

A: The solution is provided below

Q: I need parts 7, 8, and 9 answered pertaining to the print provided.

A: Geometrical dimensioning & tolerancing (GD&T) is the system used for defining and…

Q: I start from 2f₁= max, derive to this expression {fy = may, 2) ap(x, y, z) dx (_ ap(x, y, z) ay

A: For the solution refer below images.

Q: Lengths: O₂A-4 in, O3B=8 in., BC=5 in, O2O3-4 in. and offset c=10 in. Angles: 8-60° and -45° The…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: = = 2 RA 2EI 2 0 2 3RA 2EI x² dx + kNm 2 RA 2EI 3 2 (x - 3)²dx

A: According to the given data  The Bending moment expression is given by the…

Q: 90 vtams gninuoddgisn 210000 netto у19 O (a) For a given material, would you expect the surface…

A: The answer is provided below

Q: 2 Intermediate roller-pivot member ground 0/ (#1) 2-d.o.c.: F ₁ and Fu₂ where (#2) 241 241 Uz i (#3)…

A:

Q: How do integrate to get fbd= 15/28

A: It is asked to calculate the shear force in the section BD

Q: I need help answering this.

A: 1)  Only one angular dimension is shown on this print  .i.e., 16002) Two  reference dimensions are…

Q: שכוח 3. Calculate the composition, in weight percent, of an alloy that contains 218.0 kg titanium,…

A: Titaanium=Aluminum=Vanadium=The allowable element weight percentage is equal to the element mass…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.