Design the reinforcement for the following short braced column: Breadth, b = 400 mm Depth, h = 400 mm %3D h' = 320 mm fcu = 35 N/mm2 fy = 500 N/mm2 %3D Design axial load, N = 3360 kN Design moment about major axis, Mx = 224 kNm %3D Preferred main bar size = 32 mm Q3a. Determine the steel area required. Q3b. Design the main bars and links for the column.

Design the reinforcement for the following short braced column: Breadth, b = 400 mm Depth, h = 400 mm %3D h' = 320 mm fcu = 35 N/mm2 fy = 500 N/mm2 %3D Design axial load, N = 3360 kN Design moment about major axis, Mx = 224 kNm %3D Preferred main bar size = 32 mm Q3a. Determine the steel area required. Q3b. Design the main bars and links for the column.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the reinforcement for the following short braced column: Depth, h=500mm Design Axial Load, N=2500kN h'=437mm Design Moment, Mx=630kN-m Breadth, b=500mm Preferred bar size=40mm (a) Determine the steel area required. (b) Design the main bars and links for the column.
a two span beam subject to shear and flexure only is reinforced as follows: Section: TOP BARS @ midspan: 2-ø20mm @ face of supports: 5-ø20mm Section: BOTTOM BARS @midspan: 3-ø20mm @ face of supports: 2-ø20mm GIVEN: Stirrup diameter ds = 10mm concrete f'c= 21 mpa steel rebar fy= 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in a single layer. Determine the DESIGN moment strength of section at midspan for positive bending
Compute the co-ordinates for (Pnb, Mnb) and (Pub, Mub) for rectangular columns using h=24in b=14in Effective cover =3in. Reinforcement consists of 4-#9 bars on each side (totla of 8 bars) f'c=7000 psi fy=40000 psi. Use a yield strain of 0.004 for steel.
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
pls reply fast thank you
In a slab-floor system with the total depth of 22 in., the flange effective width was determined to be 40 in. The beams have a web width of 14 in. and the slab thickness is 3 in. Design the reinforcement for a typical interior beam if the factored applied moment, Mu is 9500 k-in. f’c = 6ksi and fy = 80 ksi. Draw the detailing.
show the complete solution
Q3: А- Oesign a rectangular beam with b = 350 mm, h = 625 mm as shown below. Use f! = 30 MPa, fy = 375 MPa and Ø18 mm for %3D fongitudinal reinforcement. Two lavers of tension reinforcement. PE45 kN Wu,-25 kN/m WUT14 kN/m D.L babulb 5 m B- Check the design of the singly reinforced beam shown below, if fc = 20 MPa and fy = 420 MPa, 030 mm for tension. Why? %3D sed edr arlagead iso t 430 mm 100 mm 300 mm
Please answer in 20 mins
I need help solving this exercise, and please also explain method of sections:Determine the force in members EF, EP, and LK of the Baltimore bridge truss and state if the members are in tension or compression. Use the method of sections. Also, indicate all zero-force members.
1. A one-bay one-story frame, shown in the Fig. 1, consist of a truss system. Two different types of connections are proposed for the 1s joint. Check the all requirements for tension. All dimensions are given in cm. M20 bolts with standard holes are used. S355 Structural Steel is used in all parts (F 355 MPa and F-490 MPa). 2 3 Lateral Load Please explain the solution, step by step! For example sketch the net areas show how to calculated! 4 5 An IPE beam is used to carry axial tension load (P) for the 4th member. a. Calculate the tensile strength (P) of the member according to AISC 360 LRFD and ASD. b. Determine the thickness (t) of the gusset plate according to max. tensile load calculated in part (a). 4,05 4,05 IPE360 P 26 Cross-sectional View Side View Top View
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1