Design the pin ended steel column in S275 steel to withstand an axial compressive load of 2500 KN over an unsupported height of 6.0 m assuming 356 x 368 x 129 UC. Design data : B=368.3 mm, d=290.2 mm, T=17.5 mm, t=10.7 mm, rx=15.6 cm, ry=9.39 mm, A=165 cm3.

Design the pin ended steel column in S275 steel to withstand an axial compressive load of 2500 KN over an unsupported height of 6.0 m assuming 356 x 368 x 129 UC. Design data : B=368.3 mm, d=290.2 mm, T=17.5 mm, t=10.7 mm, rx=15.6 cm, ry=9.39 mm, A=165 cm3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 40 kN/m, LAB = 1.8 m, LBC = 3.6 m, and LcD = 1.8 m. Consider the entire 7.2 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). LAB LBC LCD WT305 x 41 Answer: (a) OmaxT= MPa (b) ƠmaxC= MPa
AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 56 kN/m, LAB = 1.0 m, LBc = 2.0 m, and LCD = 1.0 m. Consider the entire 4.0 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). y LAB LBC LCD WT305 x 41 Answer: (a) OmaxT= MPa (b) Ơmax.C = MPa
AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
A WT305 x 41 standard steel shape is used to support the loads shown. Assumew= 40 kN/m, LAB = 1.2 m, LBc = 2.4 m, and LCD = 1.2 m. Consider the entire 4.8 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). В LAB LBC LCD WT305 x 41
Rigid member BED is supported using steel rods AB, CD, and EF as shown below. E-200 GPa for steel. If a force P is applied at E, determine: a) The stress in each rod b) The length of each rod after applying the force LI (mm) LI (mm) P (kN) AAB (mm2) ACD (mm?) AEF (mm) 395 350 20 250 250 450 L1 L2 Note: BE ED P.
Calcualte the following: Total factored floor load in 2 decimal places, ___ kPa Total factored uniform load on girder GH in 2 decimal places, ___ kN/m Maximum ultimate bending moment at discontinuous end of girder JK to the nearest whole number = ___ kN·m
The stiffness matrix of the beam shown below is - 1. (2 В El 2EI 4m 8m A.
Please Determine the axial load strength and moment (without and with reduction factor) a square columns for the following conditions and draw their interaction diagrams (note the scale): When conditions are in balance During the tensile condition When the pressure condition Pure axial Pure moment
Determine the maximum load that an 8 foot long 2"x4" rectangular aluminum alloy bar (E = 10.5x10^3ksi, σY = 40 ksi) can support with a factor of safety of 3 for both crushing and buckling if it has endconditions of:a. Pinned-pinned.b. Pinned-fixed.c. Fixed-free.d. Fixed-fixed.
AWT305 x 41 standard steel shape is used to support the loads shown. Assume w= 58 kN/m, LAB = 1.8 m, LBc=3.6 m, and Lco = 1.8 m. Consider the entire 7.2 m length of the beam and determine: (a) the maximurm tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). y LAB LBC LCD WT305 x 41 Answer: (a) Omax,T МPа (b) omax,C= МРа
A WT305 × 41 standard steel shape is used to support the loads shown. Assume w = 48 kN/m, LAB = 1.6 m, LBC = 3.2 m, and LCD = 1.6 m. Consider the entire 6.4 m length of the beam and determine:(a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and(b) the maximum compressive bending stress at any location along the beam (enter a negative answer). (c) Calculate the reaction forces at B and E. Forces are positive upwards.
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows: Ag = 14,500 sq.mm, Ix= 258.6 x10^6 mm ^4 Iy=84.375 x 10^6 mm^4. 55. calculate the critical slenderness ratio with buckling about strong axis.