Design Problemfor the control system shown in Fig. 6.18, obtainthe followingthe values of K and I to satisfyspecifications,.●steady-state error = 0Maximum overshoot 5%settling time 3 sec.R(S)K(HCS)(with a 2% criterion)وحدتیJ= 150 kg-m²Fig. 6.18 Feedback Control systemC(S)

Given data Forward path gain, Gs=K1+τs1Js2 Feedback magnitude, Hs=1 The feedback is of negative…

Design Problem For the control system shown in Fig. 6.18, obtain the values of K and I to satisfy the following specifications, ♦ . ● steady-state error = 0 Maximum overshoot 5% settling time R(S) & T3 sec. (with a 2% criterion) K(HCS) JS2 کل J= 150 kg-m² Fig. 6.18 Feedback Control system C(5)

Design Problem For the control system shown in Fig. 6.18, obtain the values of K and I to satisfy the following specifications, ♦ . ● steady-state error = 0 Maximum overshoot 5% settling time R(S) & T3 sec. (with a 2% criterion) K(HCS) JS2 کل J= 150 kg-m² Fig. 6.18 Feedback Control system C(5)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

6.12 in section 5.5 it was stated that the brushes may be shifted from the q-axis unintentionally, for example due to incorrect positioning, or they may be shifted intentionally to improve commutation, as explained in section 6.5.3. in section 5.5 it was also stated that, when the brushes are shifted, armature reaction may be magnetizing or demagnetizing. Sketch suitable developed diagrams to verify that when the brushes are shifted to improve commutation, armature reaction is always demagnetizing.
Q6) select the right choice for the following sentences: 1. The critical resistance of the d.c. generator is the resistance of (a) armature (b) field (c) load (d) brushes 2. The external characteristic of a shunt generator can be obtained directly from its....characteristic. (a) internal (b) open-circuit (c) load-saturation (d) performance 3. Which of the following d.c. generator cannot build up on open-circuit ? (a) shunt (b) series (c) short shunt (d) long shunt 4. If a self-excited d.c. generator after being installed, fails to build up on its first trial run, the first thing to do is to (a) increase the field resistance (b) check armature insulation (c) reverse field connections (d) increase the speed of prime mover. 5. The voltage regulation of an over compound d.c. generator is always.. (a) positive (b) negative (c) zero (d)high 6. When load is removed, . . motor will run at the highest speed. (a) shunt (b) cumulative-compound (c) differential compound (d) series 7. The Ta /I a…
(C): For a close loop system, find the values of the damping ratio (5) and natural frequency (wn) to yield a peak time of 0.356 second and a settling time of 0.808 seconds.
4. Why the O.C.C. characteristic is non-linear?
Q4) select the right choice for the following sentences: 1. The critical resistance of the d.c. generator is the resistance of (a) armature (b) field (c) load (d) brushes 2. The external characteristic of a shunt generator can be obtained directly from its......characteristic. (a) internal (b) open-circuit (c) load-saturation (d) performance 3. Which of the following d.c. generator cannot build up on open-circuit? (a) shunt (b) series (c) short shunt (d) long shunt 4. If a self-excited d.c. generator after being installed, fails to build up on its first trial run, the first thing to do is to (a) increase the field resistance (b) check armature insulation (c) reverse field connections (d) increase the speed of prime mover. 5. When load is removed, .......... motor will run at the highest speed. (a) shunt (b) cumulative-compound (c) differential compound (d) series
Explain in your words given below
control system please answers as soon as possile
4. A laser guidance system was used to control the boring machines drilling the channel tunnel to ensure that the machines, which were drilling from either end, met in the middle. The desired angle of heading of the boring machine y,, compared with the measured heading angle y and the error is used in a proportional controller of gain Kp, Figure Q4. Encountering non-uniform layers of earth or rock can cause disturbances in the heading of the boring machine denoted by D(s). (a) Derive the transfer function relating the heading ụ to the reference heading , (assuming no dis- turbance) and hence show that the steady state error due to a step change in the reference heading is zero irrespective of the value of Kp. (b) Derive the transfer function relating the heading y to the disturbance D assuming a zero reference value. (c) Calculate the natural frequency, damping, and overshoot of the system when i) K, = 50, ii) K, = 100. 1 Control 3 Section 3 Tutorial: Feedback Control Systems D(s)…
7- An 8-pole d.c. machine of 1200kW, 600v, 500 rpm and the average value of the reactance voltage per coil is 6.6V. the machine is lap connected of 648 conductor and each coil has two turns, the axial length of the compole 29 cm and the air gap is 0.8 cm, the armature diameter is 0.35m and the ratio (Bmax/Bay) = 1.5. Find the interpole m.m.f. %3D
The desired roots in complex plane should be place in such a way that the system achieves minimum settling time having undamped natural frequency equal to 2. The state variables are voltage across capacitor (also the output) and current through inductor. plz provide answer for x=21 asap
Which of the following sensors has a permanent magnet inside? Hall effect sensor thru-beam optical sensor piezo-electric sensor LVDT capacitive proximity sensor |o|0|0|6
A time-varying magnetic field linking a stationary loop induces Vtr emf Select one: O True O False