7- An 8-pole d.c. machine of 1200kW, 600V, 500 rpm and the average value of the reactance voltage per coil is 6.6V. the machine is lap connected of 648 conductor and each coil has two turns, the axial length of the compole 29 cm and the air gap is 0.8 cm, the armature diameter is 0.35m and the ratio (Bmax/Bay) = 1.5. Find the interpole m.m.f.

7- An 8-pole d.c. machine of 1200kW, 600V, 500 rpm and the average value of the reactance voltage per coil is 6.6V. the machine is lap connected of 648 conductor and each coil has two turns, the axial length of the compole 29 cm and the air gap is 0.8 cm, the armature diameter is 0.35m and the ratio (Bmax/Bay) = 1.5. Find the interpole m.m.f.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q3) The armature of a 4-pole DC machine has 240 coils wound in lap formation. Each coil generates a voltage of 4 V and carries a current of S A. a) Calculate the total generated voltage in the armature,Eg. b) Find the current in each parallel path and total armature current. c) If the armature is rewound in wave formation, find the generated voltage, Eg. current per path and total armature current. Assume number of coils are fixed at 240.
Please solve thiss questionnnnn
For the design we assuming following parameters 1) winding : Lap 2) simplex 3) Number of slots : 16 , single turn coil with 2 conductors per slot 4) Number of poles = 4
The synchronous reactance of a cylindrical rotor machine is unity. The machine is connected to an infinite bus bar through an equivalent reactance of half of its synchronous reactance. For a maximum power output of 1.3 p.u. delivered at 1.02 p.u. voltage, find E. While the field is undisturbed, find the value of the current if the real power output is reduced to 0.65.p.u.
A 220 V , 60 Hz , supply is connected to 200 – turn armature winding of reluctance 1.7x105 At / Wb . Find the magnetizing reactance , the rms values of the ( magneto – motive force , exciting and armature currents , magnetic flux ) , and the inductance Draw the phasor diagram of the circuit .
A 4 pole armature of a DC machine has 175 conductors and a flux per pole of 0.1 wb. Find the EMF generated when running at 600 rpm, when the armature is Lap wound.
Write a MATLAB program describing the following figure. one cycle TIME PRESSURE amplitude
(B)-Explain by drawing the change in the direction of current flows through coils at the ideal case of commutation by considering coil B which is the coil under commutation as shown in the figure below. B C 5A SA 5A Armature winding 10 A Commutator 10 A Brush
For a 4-pole dc armature with 28 slots and 8 coil-sides per slot, find the winding pitches and the commutator pitch for a wave winding. What is the distance between brushes in terms of commutator segments?
The current generated by the waterwheel generator changes direction as the wheel rotates, that is, it is an alternating current. Could you design a simple generator like this that would induce a current that continuously flowed in one direction (a DC current)? If not, explain why not. If so, describe and sketch your model solution below.
The field winding of a.d.c. machine takes a steady current of 10A when connected to a d.c. source of 230 volts.On, switching the voltage to the field, it is observed that it takes o.3 second to reach 5 A. (i) Find the value of inductance of the field winding. (ii) Find also the time for the current to fall to 30% of the final steady value if the field terminals are short - circuited.
× 4:03 K s.eng.ruh.ac.lk □ Û 8. Figure 4 shows the core of a simple dc motor. The magnetization curve for the metal in this core is given by Figure 5 and Figure 6. Assume that the cross-sectional area of each air gap is 18 cm² and that the width of each air gap is 0.05 cm. The effective diameter of the rotor core is 4 cm. L It is desired to build a machine with as great a flux density as possible while avoiding excessive saturation in the core. What would be a reasonable maximum flux density for this core? ii. What would be the total flux in the core at the flux density of part (i)? iii. The maximum possible field current for this machine is I A. Select a reasonable number of turns of wire to provide the desired flux density while not exceeding the maximum available current. Flux Density, B (T) 2.8 སྤྲ ཤཱ ཀ ཀཱ བྷ ཀ ཡཱཾ བ ་ 1.2 1.0 0.4 0.2 4-48cm Figure 4 0 10 20 30 40 50 100 → Depth 4 cm -0.05 cm 200 300 500 1000 2000 Magnetizing Intensity, H (A.turns/m) Figure 5 Magnetization curve…