Design an I-section purlin, for an industrial building situated in the outskirts of Allahabad, to support a galvanised corrugated iron sheet roof the following data: Spacing of the truss c/c = 6.0 m Span of truss 12.0 m Slope of roof = 30° Spacing of purlins c/c = 1.5 m Intensity of wind pressure = 2 kN/m² Weight of galvanised sheets = 130 N/m² Yield stress of steel = 250 MPa Use Is Code

Design an I-section purlin, for an industrial building situated in the outskirts of Allahabad, to support a galvanised corrugated iron sheet roof the following data: Spacing of the truss c/c = 6.0 m Span of truss 12.0 m Slope of roof = 30° Spacing of purlins c/c = 1.5 m Intensity of wind pressure = 2 kN/m² Weight of galvanised sheets = 130 N/m² Yield stress of steel = 250 MPa Use Is Code

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1: The truss shown below is made of fiberglass members with a 30 mm square cross section and an axial strength of 14 MPa, and is assembled with high strength nylon pins with a 20 mm diameter and a shear strength of 25 MPa. The ends of the members are reinforced. If the structure requires a minimum safety factor of 2.5, find the largest load P that can be safely applied at point A. A PV -2 m D B -2 m E 1.5 m 1.5 m 1.5 m A-30mm
7:49 ll ? 1 Gmail h.w. 1.jpg A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Fig. Axial loads are applied at the positions indicated. If P 3000N and the cross sectional area of the rod is 325 mm2, determine the stress in each section, and total deformation of the road. E for steel is 200000 MPa, E for aluminum is 70000 MPa, E for bronze is 100000 MPa 4P Steel Bronże O | Aluminum PO D.9 ~回

Problem 1
Civil
3G KOREK docs.google.com/forms Q2: The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1040Q&T 400F0 wire. The spring has 82 coils and is close-wound with a preload of 18 Ibf. (a) Find the closed length of the spring.(b) Find the torsional stress in the spring corresponding to the preload.(c) Estimate the spring rate. (d) What load would cause permanent deformation?(e) What is the spring deflection corresponding to the load found in part d? 0.162 in - in R 글-in R. Option 1
What is the maximum concentrated load that can be applied at the end of an embedded hollow pipe, made of AISI 1020 steel? Take 10.16 cm for the outside diameter, and 6.35 cm for the inside diameter. The length of the pipe is 183 cm. Its maximum deflection must not exceed 5.08 cm. Neglect the weight of the pipe. Answer 22816 N
Determine the degree of indeterminacy of the trusses as shown.
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
Please answer with a complete solution. Thank you! The roof truss is supported by a hinge at A and a horizontal roller support at B. The wind loads are perpendicular to BC. Determine the reactions at A and B.
A framing anchor is formed of 0.05-in.-thick galvanized steel. Determine the mass moment of inertia of the anchor with respect to each of the coordinate axes. (The specific weight of galvanized steel is 470 lb/ft3.)
Identify and describe the functional classification of roads with respect to the following road agencies in Ghana; Ghana Highway Authority (GHA), Department of Urban Roads (DUR) and Department of Feeder Roads (DFR).
Solve ASAP