Design a suitable diameter for a circular shaft required to transmit 90 kW at 180 r.p.m. The shear stress in the shaft is not to exceed 70 MPa and the maximum torque exceeds the mean by 40%. Also find the angle of twist in a length of 2 metres. Take C= 90 GPa. [Ans. 80 mm; 2.116°] %3D

Design a suitable diameter for a circular shaft required to transmit 90 kW at 180 r.p.m. The shear stress in the shaft is not to exceed 70 MPa and the maximum torque exceeds the mean by 40%. Also find the angle of twist in a length of 2 metres. Take C= 90 GPa. [Ans. 80 mm; 2.116°] %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Power transmitted by a hollow shaft at 300 rpm is 800 kW. The ratio of outer diameter to the inner…

A: Given data:- power=800Kw N=300rpm dodi=1.5 Tmax=1.4 Tmean τper=80 MPa…

Q: A tubular aluminum alloy [G = 4,000 ksi] shaft is being designed to transmit 390 hp at 1,600 rpm.…

A: Given :For aluminum alloy- To find:Minimum permissible outside diameter.

Q: Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller…

A: Given data specification of the propeller shaft Power transmission (P) = 270 kW Speed (N) = 65 rpm…

Q: A compound steel [G = 70 GPa] shaft consists of a solid 59-mm-diameter segment (1) and a solid…

Q: Q2: A solid steel shaft 450 mm long is stressed at 75 MPa when twisted through 3° and used to…

Q: Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller…

Q: Find the required diameter d0 for a solid circle shaft. b) Find the required outer diameter d2 for a…

A: Given: T =1200 NM G=78 GPa Allowable shear stress =40 MPa Allowable rate of twist 0.78/m TO…

Q: Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above…

A: Solution:

Q: A solid stainless steel [G = 93 GPa] shaft that is 2 m long will be subjected to a pure torque of T…

Q: В x (in) r = 2e0.05x 100 kip-in r (in) A 10 in 100 kip-in The solid torsional shaft above is…

Q: A solid shaft in a rolling mill transmits 30kW at 100 rpm. Find the diameter in mm of the shaft so…

A: Answer: The diameter of the shaft is 63.35 mm. Hence, the correct answer is option (c).

Q: Q2: For the shaft shown in Figure 2, find the maximum shearing stress in the Aluminum and the steel…

Q: Find the max shear stress in given data of two circular shafts (S) AND (H)

A: GIVEN DATA; Two circular shaft made same material one solid and one hollow both have same length…

Q: A circular steel shaft with length, L (m) has an outer diameter, d2 (mm) and inner diameter, d1…

A: To find: The angle of twist in degrees. Given: The inner diameter is d1=100 mm1 m1000 mm=0.1 m. The…

Q: The compound shaft shown in the figure consists of two steel [G = 80 GPa] pipe segments. The shaft…

A: Given Data:The modulus of rigidity of steel is..The outside diameter of segment 1 is..The wall…

Q: Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller…

Q: For the gear system shown in the figure, the diameter of shaft AB=12 mm. Determine the diameter of…

Q: A solid shaft 18 m Length is to transmit power at 2200 rpm. If the shaft is stressed to 275 MPa when…

Q: A hollow shaft transmits 7 MW at 200 rev/min. It is supposed that the maximum allowable stress is…

A: Given, P=7 MW=7×106 WN=200 RPMτ=70 MN/m2=70×106 N/m2G=80 GN/m2=80×109 N/m2θL=0.40/m=0.4×π180…

Q: (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and…

A: Given data Outer Diameter of Tubular shaft = Do = 50 mm = 0.05 mInner Diameter of Tubular Shaft = Di…

Q: A hollow steel shaft, 12 m long, is required to transmit 1000 kW when running at a speed of 300…

A: Given that , L=12m =12000mm P=1000 kW =1000×106N-mm/s

Q: is 300 rpm and transmit the same power. The speed of shaft 'A' is 250 r.p.m. and that of shaft B…

A: we have to compare the diameters of shaft A and B

Q: A tubular steel [G = 79 GPa] shaft with an outside diameter of D = 89 mm and a wall thickness of t =…

A: Given Data The modulus of rigidity is: G=80 GPa The outside diameter is: D=89 mm The thickness of…

Q: A solid 1.250-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 175 lb-ft and…

Q: A hollow steel propeller shaft, 20 ft. long with 15 in outer diameter and 12 in. inner diameter,…

Q: Find the twisting moment in a solid shaft 125 mm diameter when the angle of twist is 0.5 degree on…

A: Introduction When a…

Q: Q6. A hollow circular shaft has an external diameter of 120 mm and the internal diameter is…

A: The inside diagram can be determined as shown below.

Q: 7. A shaft with a length of 5 m is subjected to a twisting moment of T=4x10 N.mm. If J=620x10 mm,…

Q: 0.6 m 1 m 1200 N.m d,= 30 mm- B A 800 N.m d, = 60 mm Figure 4 c) Consider a shaft in Figure 4 is a…

Q: A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum…

A: Given, Length of shaft = L = 1 m Power transmitted = P = 30 kW = 30 x 103 W Shaft RPM = 700 rpm…

Q: A solid shaft 2 m. long is stressed 60 MPa when transmitted a power of 50 kW at 2 rev / sec. If G =…

A: Given :- Length, L = 2m Power, P = 50kW Rotational speed, n = 2 rev/s…

Q: A compound steel [G = 83 GPa] shaft consists of a solid 58-mm-diameter segment (1) and a solid…

Q: 2 PUII The figure below shows a shaft of three segments. It is restrained (fixed support) at both…

Q: d; = 20 mm A) A hollow rod, shown in figure, having an inner diameter of d;=20 mm and an outer…

A: Given Data Inner diameter is: di=20 mm Outer diameter is: do=25 mm Shear stress is: τ=570 MPa Speed…

Q: A steel shaft with a diameter 1.95 inches and length 4.35 feet transmits 80 HP from an electric…

A: Given dataDiameter = d= 1.95 incheslength = 4.35 feetAllowable shear stress = τallow = 8600…

Q: A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum…

A: Given:Length of the hollow shaft, L=1 mPower transmit, P=30 kWSpeed of the shaft, N=700 rpm,Angle of…

Q: A steel shaft in the form of a solid body circular rod or a circular tube can be manufactured. The…

A: given torsional torque T=1200 N.mshear stress for shaft material τ= 40 MPalargest permissible unit…

Q: The bending stress at point A.

A: Given data Outer Diameter of Shaft = Do = 50 mm = 0.05 mInner Diameter of Shaft = Di = 40 mm = 0.04…

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Design a suitable diameter for a circular shaft required to transmit 90 kW at 180 r.p.m. The shear
stress in the shaft is not to exceed 70 MPa and the maximum torque exceeds the mean by 40%. Also
find the angle of twist in a length of 2 metres. Take C= 90 GPa.
[Ans. 80 mm; 2.116°]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. [-/1 Points] DETAILS GGMECHMAT9 3.7.006. The drive shaft for a truck (outer diameter 80 mm and inner diameter 25 mm) is running at 2,300 rpm (see figure). 2,300 гpm 80 mm 25 mm 80 mm (a) If the shaft transmits 150 kW, what is the maximum shear stress in the shaft? (Enter the magnitude in MPa.) MPа (b) If the allowable shear stress is 30 MPa, what is the maximum power (in kW) that can be transmitted? kW
A solid 2.0 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3300 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 590 rpm? What is the maximum shear stress developed in the shaft? Answer: P = hp psi Save for Later Attempts: 0 of 1 used Submit Answer
Mechanics of deformable bodies
3) Two circular shafts (shown in Figure) made of the same material and have the same length are subjected to a torque Tequals 150 lb.ft, the angle of twist for the hollow shaft equals that of the solid shaft. A-1/3 C-5.4 B-1 D-3 D=10 in solid shaft D=10 in d=9 in O hollow shaft
Question 3 A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm respectively and transmits 8000 kW at 100 r/min. 3.1 Calculate the maximum shear stress in the hollow shaft. /4/ 3.2 Calculate the shear stress on the inner surface of the hollow shaft. /2/ an 3.3 Determine the maximum length of this shaft if the maximum shear stress as well angle of twist of 30 is not to be exceeded. (G = 80 GPa) /3/ 3.4 If this shaft is connected to a similar shaft, 1 m long, through a 10-bolt rigid flange coupling, determine the minimum standard bolt diameter if the pitch circle diameter of the coupling is pcd = 450 mm and the allowable shear stress in the bolts should not exceed 55 MPa. /3/ 3.5 Determine the equivalent torsional stiffness of the shaft assembly. /3/ [15]
8.4 (A). A hollow shaft has to transmit 6 MW at 150 rev/min. The maximum allowable stress is not to exceed 60 MN/m² nor the angle of twist 0.3° per metre length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m² [61.5 mm.]
Example 7.5: (Numerical problem of a circular shaft) A circular shaft 10 cm diameter and 1.1 m length is required to transmit power with a maxi- mum angle of twist of 3°, (a) What is the maximum possible torque that can be transmitted by this shaft? (b) Find the maximum shear stress induced. (c) Find the maximum possible power transmitted for N = 1500 rpm. Given that modulus of rigidity G 8% 101M Pa.
Find the length of solid shaft (L=?) in the rolling mill transmits 10KW at frequency 2r/s. Diameter of the shaft is 60mm. #f the shearing stress is not exceed 60MPa and the angle of twist is limited to 5°. G=836 836P2 Length of Shaft, -L=?
A solid stainless steel [G = 108 GPa] shaft that is 1.2 m long will be subjected to a pure torque of T = 82 N-m. Determine the minimum diameter d required if the shear stress must not exceed 40 MPa and the angle of twist must not exceed 4.7°. Report both the maximum shear stress 7 and the angle of twist at this minimum diameter. Answers: d = mm. T = IN i MPa. i
For the circular shaft (G=12×106 psi) shown below: a. Compute the reaction torque and draw the torque (T) diagram. b. Find the max shear stress (Tmax) along the shaft. c. Compute the angle of twist AE at E. 1000 lb in 500 lb in 800 lb. in A B 2 in 2 in + 3 in D 5 in to E AC CD 2 DE
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
A solid 1.500-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 190 lb-ft and TD= 140 lb-ft, acting in the directions shown. Assume a = 42 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 20 ksi, determine the maximum torque TC that can be applied to the shaft.