Design a round spiral column to support an axial dead load of 950 kN and an axial live load of 1210 kN. Use fy = 276 MPa and f’c = 27.6 MPa. Assume 2% steel ratio and use 28 mm main bars and 10 mm spiral. Assume a steel concrete cover based on NSCP 2015

Design a round spiral column to support an axial dead load of 950 kN and an axial live load of 1210 kN. Use fy = 276 MPa and f’c = 27.6 MPa. Assume 2% steel ratio and use 28 mm main bars and 10 mm spiral. Assume a steel concrete cover based on NSCP 2015

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular concrete beam has a width of 300mm and an effective depth of 550mm. The beam issimply supported over a span of 6m and is used to carry a uniform dead load of 25 kN/m and a uniformlive load of 40 kN/m. Assume fc’ = 21 MPa and fy = 312 MPa. Compression reinforcement, ifnecessary, shall be placed at a depth 80 mm from the outermost compression concrete. Used loadcombination of 1.4DL + 1.7LL. 4. Determine the required compression steel area in square millimeters.5. Determine the required number of 25-mm compression bars.
The beam is simply supported on a span of 6 m and carries a load of 18 KN/m. Use ACI Specifications withfc’ = 17.2 MPa, fs = 124 MPa, n = 12, d’ = 65 mm, and ?concrete = 23.54 KN/m3.(a) service moment (f) use b = 250 mm, d = Answer (round down to nearest 25 mm) + 50 mm(b) fc to take care of dead load(c) k (g) h (h) dead load (i) total load(d) j (j) recompute service moment (k) check effective depth(e) R (l) use 28mmɸ for As (m) check main bar clear spacing
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. bottom is 70 mm. Use concrete strength f'c = 21 MPa and steel yield strength fy = 345 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN-m of the beam Concrete cover to bar centroid at the top is 80 mm and at the in negative bending. Write the answer in 2 decimal places only.
I need the answer to the question in reinforced concrete
Design a square base plate to support 10 mm thick pipe column with an inside diameter of 300 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 850 kN and PLL =420 kN. Assume that the pipe is to rest on a very wide slab. Use A-50 steel and concrete fc’ = 35MPa and LRFD.
Pb- DCS.
Qz- Find the, Critical load Pe using E=2x1ổ Pc Pery 4m
1. A rectangular beam has b = 300mm, d = 500mm, As = 6 – 32mm diameter bars, fc' = 27.6 MPa, fy = 414 MPa. Calculate: a) depth of compression block, "a" b) fs c) + d) Mu
A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa and fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm² 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment 3. Determine the maximum number of 25 mm diameter bars to be provided to have a tension controlled section Answer 1: 2403.21 correct answer: Answer 2: 9.00 Answer 3: 8.00
A 15 x 25 in. column is reinforced with four No. 9 (No. 29) bars, one in each corner as shown in Figure (a). The concrete cylinder strength is f. = 4000 psi and the steel yield strength is 60000 psi. Determine the axial load strength for zero eccentricity without subtraction of the concrete displaced by the steel, as well as with subtraction of the concrete displaced by the steel. E=0.003, E,-29000. Imperial Metric bar Linear Mass Density Nominal diameter Nominal area 25" bar size size (soft) Ib (in) (mm) (in') (mm") 2.5" -2.5" 0.250 - % 6.35 0.05 32 0.375 = % 9.53 0.11 71 0.500 = 4 12.7 0.20 129 0.625 = % 15.9 0.31 200 0.750 = % 19.1 0.44 284 0.875 = % 222 0.60 387 1.000 = % 25.4 0.79 510 1.126 - % 28.7 1.00 645 1.270- 1% 32.3 1.27 819 No.6 0.167 0.249 3 No. 10 0.376 0.560 #4 No. 13 0.668 0.994 Pn #5 No. 16 1.043 1.552 15" No. 19 1.502 2.235 #7 No.22 2.044 3.042 #8 No 25 2 670 3.973 As No 29 3.400 5.060 A's #10 No 32 4.303 6.404 e varies #11 No.36 5.313 7.907 1.410- 35.8 1.56 1.006…
AT-Beam has the following properties: bf = 750 mm, bw = 275 mm, d 560 mm, t = 115 mm. Concrete compressive strength fe 21 MPa and steel yield strength fy 415 MPa. T-Beam is under factored moment load of 720 kN-m. Locate the compression block under balanced condition from the extreme compression fiber.
Determine end reaction for Beam 1 (B-1). L1 L2 B-1 L2 L2 L2 • L1 = 20 ft • L2 = 6 ft Live load = 50 psf • 4" Thick concrete slab (density = 150 pcf) • 5/8" Thick terrazzo (12 Ib/ft2/in) • Beam weight = 30 lb/ft Girder weight = 22 lb/ft Please round to the nearest one. One end reaction for B-1 = Ibs MacBook Air 吕0 F3 F7 F4 F5 F2 & * @ 7 8. 2 3 W E R T Y