Design a linear oscillator, using a Hartley configuration, to generate oscillating signal at frequency f = 15 kHz by choosing an appropriate value of L1 and L2, knowing that the inductance is C = 200 µF, the transconductance when the transistor is biased in operation is gm = 2.5 mS and the gate resistance Rg = 5 kN. %3D (a) Draw the electric circuit and explain the role of each component. (b) Derive the small signal equivalent model of the open loop circuit and state your main assumptions. Derive the oscillation condition. State any assumptions you make and show all steps of your calculation (c)

Design a linear oscillator, using a Hartley configuration, to generate oscillating signal at frequency f = 15 kHz by choosing an appropriate value of L1 and L2, knowing that the inductance is C = 200 µF, the transconductance when the transistor is biased in operation is gm = 2.5 mS and the gate resistance Rg = 5 kN. %3D (a) Draw the electric circuit and explain the role of each component. (b) Derive the small signal equivalent model of the open loop circuit and state your main assumptions. Derive the oscillation condition. State any assumptions you make and show all steps of your calculation (c)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

IRL RL In the circuit using a Zener diode above, given that V, = 10 V, R= 3.7 KO, R 6.8 KQ, and the Zener voltage Vz = 5 V. a) The current IRL through the load resistor is b) The current fiowing through the resistor R is:
double clipper circuit Zener diodes 1N4733A has a voltage of 5.1 V and 1N4735A has a voltage of 6.2 V with a resistor R=300ohms has been used. you may like to increase the input to a 12 VRMS AC source in order to see the clipping at 7volt. Please, Do the theoretical calculations and plot the expected waveforms by hand. ( I have its multisim design and only needs theoretical calculation and hand drawn graph of it to compare to its data that I have collected from multism.) Thanks
Kindly solve all the parts for me
In the given circuit, D1 is Silicon diode and D2 is a zener diode with breakdown voltage of 6.8V. Assuming RC time constant of circuit >> T. Find the Maximum and Minimum value of the output waveform.
a2/a-Design Circint as the following peseripton: A. the positive cycle of the vout signal is 3.2 and Neyatine cycle is 4.3 (Note: we must used preetical Diodes aned vin is tov) B- the pesitive cycles of vout is s-3 od Negative cycle is (5 4) [te:Comsider vin = 1ovavd we must used Capaetor with praeticul Didde)
Question 4. Design a limiter circuit using only diodes and 10 K resistor to provide an output signal limited to +1.4 V.
6:39 Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=5 V and V2=9 V. www Vin Vout Maximum voltage of output waveform Minimum voltage of output waveform
Using a positive Clamper with positive biasing voltage Circuit, with an AC voltage of Vi = 20v with a frequency of 60hz, a value of 500n for the Capacitor, a silicon diode, biased voltage voltage of 5 volts and a resistor with the value of 300 ohms. Find the current on the resistor at a simulation of 20ms in mA. Vm 2Vm R V,m Vo -Vm V, Input Waveform Output Waveform Positive Clamper with positive reference V, www
20. A biased clamper is connected to a rectangular AC input with 20V on the positive half cycle and -10V on the negative half cycle. The orientation of the Si diode is the same with Vo while the 5V biasing voltage is in opposite connection. The value of R is 100K ohms while the capacitor is 1 microFarad.
Find Idc, Vdc and the capacitance that will force the Vr(pp) to 3mV. Draw the output waveform across the capacitor. Fin=60Hz.
An RC filter stage (R = 42 Q, C = 220 µF) is used to filter a signal of 30 V de with 6 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 200-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.