Design a helical compression spring for a maximum load of 1000 N and deflection of 25mm taking Wahl’s factor into consideration. Assume spring index as 5, maximum permissible shear stress for spring wire as 420 MPa and modulus of rigidity as 84 kN/mm2

Q: A steel helical compression spring of an average coil diameter of 16 mm with a wire diameter of 1,4…

A: As per given question  Coil diameter =16mm Wire diameter =1.4mm Active coil =6 Gsteel =80 gpa We…

Q: A 'L' shaped post with a cylindrical cross-section is loaded with a concentrated load at its free…

A: Given: To find: State of stress at P1

Q: The figure Q3 below shows a bolt holding together two components. The bolt has a load bearing…

A: Thickness of component 1, t1 = 5 mm Thickness of component 2, t2 = 10 mm Modulus of elasticity of…

Q: An overhead crane can be modelled as the beam system shown in Figure Q3. The beam of length L = 7.2…

A:

Q: The following figure represents a 3-nodes, two-element truss structure with identical…

A: We have to determine the displacement at the global node 2 of the inclined roller in its local…

Q: Pravinbhai

A: The objective of the question is to calculate the deflection at pulley B and point C of a steel…

Q: Calculate the thickness and number of leaves of a semi-eluptic carriage spring which is required to…

A:

Q: A forged steel link with uniform diameter of 30mm at the centre is subjected to an axial force that…

A: Given:d=30 mmPmax=160 KNPmin=-40 KNSult=600 MPaSy=420 MPaSe=240 MPa

Q: helical compression spring subjected to compressive load. The maximum shear stress induced in the…

A: Given:τmax=24 MPaFind,The maximum shear stress induced in the cross-section of the wire?

Q: Q-11 The rigid plate in Figure Q-11 is supported by bar (1) and by a double-shear pin connection at…

A: Write the given information.

Q: jected to a load which varies from W1 N to W2 N. The spring index is 6 and design factor of safety…

A:

Q: Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while…

A:

Q: Problem 11. The problem below, consists of a rod with a circular cross-section embedded and bonded…

A: Elastic deformation is a self-reversible transitory deformation of a material's shape after the…

Q: Scale a steel helical spring to safely support the F=480N axial load. Due to space limitation, the…

A: Solution: Given Data: F = 480 N D = 50 mm C = 10 G = 78400 N/mm2

Q: B/ A steel robotic arm carries a payload of (444.82 kg) has a dimension of (1.524 m) length, (0.1524…

A: A robotic arm is a very useful part of a robot that can move in multiple ways based on the…

Q: at is supporting Es will be used -s with shearing ring has a defo

A:

Q: A semi-elliptical leaf spring fully graduated which is made of stee; has a thickness of 10 m number…

A: t=10mmn(no.of leaf)=6Wspring=65mmWband=140mmE=200,000MPaσ=360MPa To-Find:- Deflection of leaf spring

Q: = 400 kN is applied at global node 2. Using the direct approach and the minimum number of linear…

A:

Q: A close plain coil helical spring has a stiffness 10 N/mm. Its length when fully compressed, with…

A: Step 1: Step 2: Step 3: Step 4:

Q: A close-coiled helical spring has stiffness of 10 N/mm. Its length when fully compressed with…

A: Springs are one of the flexible machine elements, which gets deformed when load is applied to it and…

Q: Find the equivalent spring constant of a uniform mild steel rod length of 2.5 m, cross-sectional…

A:

Q: * S. A close-coiled helical spring has stiffness of 10 N/mm. Its length when fully pressed with…

A:

Q: Ex: A close-coiled helical spring of round steel wire 6mm in diameter having 14 complete coils of…

A: solved

Q: Euler's critical buckling load

A: Given; Case of slender column of length l, and        flexural rigidity EI built-in at its base

Q: H.W (2):A helical compression spring is made of hard drawn carbon steel has a maximum permissible…

A:

Q: centric springs are constructed squared and ground ends from oil-hardened steel. The ultimate…

A: We have given Two concentric springs are constructed with squared and ground ends from oil-hardened…

Q: a uct ang ular Ahaped block with dimensions : L= 127 mm, W's 127 mm, H= 7e. 2 mm is subjected to…

A:

Q: Parvinbhai

A: The objective of the question is to determine the critical location where stress will be a maximum,…

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G=11,500 ksi] shaft is not to…

A:

Q: A helical compression spring is fabricated from ASTM A229 oil-tempered wire (Figure 14.3a) and has…

A: Note:Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: KOBLEM: THE SHAFT IN THE * CAST IRON. STRESS COM t - 2c000 PSI AND Suc RITTLE COULOMB - MOH

A:

Q: 4-8. For a close-coiled helical spring subjected to an axial load of 300 N having 12 coils of wire…

A: Given, The mean coil diameter, D=250 mm The wire diameter, d=16 mm Number of coils, n=12 Axial load,…

Q: Parvinbhai

A: The objective of this problem is to draw the shear force and bending moment diagrams for a car jack…

Q: A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P…

A:

Q: A mechanism carries a constant load P applied to the seat as E shown. Calculate the forces, in…

A: Forces in mechanisms can be calculated by balancing them in particular directions.  The sum of all…

Q: 4. A hollow steel shaft undergoes a tensile axial load P and a moment M = 2 kN-m as seen below.…

A:

Q: 3. A diver of weight W is springing on a rectangular cross-sectional diving board ABC. On a…

A: Given: weight of the diver→W=600 N height of the diver→h=500 mm = 0.5 m youngs modulus→E=12.6…

Q: Compare the differences between brittle and ductile materials. Give an example for each material…

A:

Q: A machine with a mass of M= 600 kg with a rectangular section (depth =0.1 m, width =1.2 m), L=2 m…

A: