Design a four-bit binary input (W3W2W1W0) priority encoder using necessary gates, with priority of the inputs given in the following table (input wo having the highest priority and input W3 having the lowest priority). Inputs Outputs W3 W2 W1 Wo ут Уо Z 0 0 0 0 X X 0 1 0 0 0 0 0 1 X 1 0 0 0 1 1 X X 1 0 1 0 1 X X X 1 1 1 1

Design a four-bit binary input (W3W2W1W0) priority encoder using necessary gates, with priority of the inputs given in the following table (input wo having the highest priority and input W3 having the lowest priority). Inputs Outputs W3 W2 W1 Wo ут Уо Z 0 0 0 0 X X 0 1 0 0 0 0 0 1 X 1 0 0 0 1 1 X X 1 0 1 0 1 X X X 1 1 1 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is ICEO and how is it related to ICBO? How do these two parameters change with temperature? Give typical values for each at room temperature and at maximum temperature.
Discussion : (1) رم طرة what are the advantăge and disadventage of full-wave bridge rectifier cutcuit- calculate ale practically result have been produced (2) Vpeak theortically of voltage output by using реа (3) üG Compare theortically and practically results. (4) What happens do on Vout, if we reversed the four diodes connects . sKetch the Vout in this case . 6. し 2.5 1.48 1.35
Consider the full wave rectifier circuit shown below, with a large smoothing capacitance C = 300µF placed in parallel with the load resistor RL = 1KN and Vm = 15V. Assume that the diodes are piece-wise linear with r,= 100 and V, 0.7V then derive the plot for the output voltage across the load resistor RL. Plot A V Plot C V wm Plot B V Plot D V please pick a plot
Exercise_4 A single-phase controlled rectifier bridge consists of one SCR and three diodes feed R-load: a) Draw the circuit diagram of this bridge rectifier b) Sketch output voltage waveform for a firing angle a for the SCR and hence obtain an expression for the average output voltage under the assumption of constant current. Show the conduction of various components as well. Draw waveforms of current through TI, D1, D2 and D3 assuming constant load current. c) d) For an AC source voltage of 230 V, 50 Hz and firing angle of 45°, find the average output current and power delivered to 1000 resistor. O
Please answer the question step by step and please care to explain the question in detailed with your own sentence and explain why you used that formula, calculations etc asap. Thanks in advance.
Can you solve this question by explaining your solution step by step and giving details on the formulas and calculations, please. Thanks a lot. 2) Consider a two terminal semiconductor diode a) Calculate the thermal voltage of a diode at room temperature about 27oC b) Calculate diode dynamic resistance in case of 13 mA diode current. (Boltzman’s constant is 1.38x10-23 J/K, and magnitude of electron charge is 1,6X10-19 C)
Three Phase Uncontrolled Half Wave Rectifiers find the value of Voltage and Currents (output de and Root Mean Square) with all the proved, then sketch the curve from 0-2 on these axes (vs, vo, ia, ib, ic, io) explain its operation.
Q2/Obtain state table and state diagram, also what is the type of the system moore or mealy? A CIK
I need the answer only those parts. vi,vii,viii,ix,x, Please provide correct solution. And provide **ALL** those parts what i mentioned ( vi,vii,viii,ix,x) WILL UPVOTE YOUR ANSWER IF YOU PROVIDE CORRECT SOLUTION OF VI,VII,VIII,IX,X
i need the answer quickly
A half-wave rectifier with a 270 2 load resistor operates from a 120 Vrms 60 Hz household supply current through a 3-to-1 step-down transformer. It uses a silicon diode that can be modelled as having a constant Vf = 0.84 V drop for any current. vs(t) VL (t) RL (a) What is the peak voltage, vs,peak, of the secondary? What is the peak voltage, UL,peak of the rectified output? (b) For what fraction of the cycle (in percentage) does the diode conduct? (c) What is the average output voltage, V₁? (state which formula you used: the more accurate formula obtained via integration or the approximate formula) 1 (d) What is the average output current, IL? (e) You want to create a DC source with a peak-to-peak ripple voltage, Vr, of 11% of the peak output. (1) What size of capacitor should you add across the output? (2) What is the average voltage now? (State whether you used the more accurate or the approximate formula.)