Describe the aqueous ammonia-based scrubbing system represented by the following PFD (without material balance table)

Q: What is the material and energy balance of liquid liquid extraction process

A: Liquid-liquid extraction: Liquid-liquid extraction is a separation operation in which the solute…

Q: Discuss the following:1. The similarities and dissimilarities between wet scrubbing process and gas…

A: Wet gas scrubbers are devices that are used to remove a variety of pollutants from exhaust gas from…

Q: discussion Heat transfer by natural and forced convection .

A:

Q: For heat transfer, the surface resistance was characterized by a convective heat transfer…

A: For convective heat transfer the heat transfer quotient h is given by:

Q: 2. Label the names of the following membrane filtration operation modes at the bottom of the images

A: This is dead end flow  The particles are trapped within membrane and all water   Will pass…

Q: With an aid of a diagram, compare between FOUR (4) ideal gas flow patterns in a membrane separator

A: ideally there are four different flow patterns for membrane separation process:1)complete…

Q: What is the name of the device shown in the figure? Feed Packed Drying fuel bed Pyrolysis Air Air…

A: Updraft gasifier An updraft gasifier is also known as a counter-current gasifier where the air…

Q: Determine the terminal settling velocity of a coal particle of size 400 micron in water at 20 oC by…

A: We need to find settling velocity of coal particle water and then we need to compare it with…

Q: Water at 150 °C flows on the inside of a 1 meter long 2" Schedule 80 steel pipe (thermal…

A: Dear User, Kindly note that according to bartleby policy, we can answer only 3 subparts from the…

Q: 6. Which ratio of cathode to anode accelerates galvanic corrosion? a. Larger cathode to smaller…

A: In general, the rate of corrosion is significantly impacted by the relative sizes of the cathodic…

Q: We wish to produce 0.2-in-diameter wire of copper having a minimum yeild strength of 60,000 psi and…

A:

Q: B. Below is an image of typical data for the thermal analysis of a polymer sample on differential…

A:

Q: List three types of annealing used in thermal processing of metals, and describe ONE in detail.

A: according to Bartleby's guidelines, I can only solve one question at a time 3) three types of…

Q: How to improve heat transfer by ultrasound: application For a double tube heat exchanger ???

A: A Heat Exchanger is used to utilize the heat of the product stream, in general, to other streams…

Q: Given the table below and your judgement for extreme operational conditions, select polymers for the…

A: Given Data Different Material With their Glass Transition Temperature and Melting Point.  To find…

Q: identify a specific process industry of heat exchanger evaluate the use of heat exchanger in the…

A: A process industry is to be mentioned where heat exchanger is used along with the applications of…

Q: How membrane separation process can be relate to the fundamental of heat/mass transfer?

A: The membrane separation process is a very important water treatment process in which the mass…

Q: Because intermolecular forces can only be controlled at surfaces & interfaces. Because of the high…

A:

Q: A steel coupon with an anode surface area of 1000 cm2 is placed in an electrolyte. The corrosion…

A: As the  metals are found in the ores present naturally in the environment. The corrosion process can…

Q: v Abrasive A. Fireclay v High thermal shock resistance B. Whiteware clay ceramic v Washbasin C.…

A: To match entries in the left column with those in right column

Q: Discuss the classification of heat exchangers.

A: Heat exchangers are those equipment's which is used to transfer heat from a hot fluid to a cold…

Q: 6-Calculate the overall heat transfer coefficient based on the inner diameter for a steel pipe…

A: Given, The inner diameter of the pipe, di = 20 mm The thickness of the pipe, δs = 2 mm The thickness…

Q: Plate filter press is commonly used in industry due to its high strength, long service life and good…

A: tbatch = 60 min = 1 hr tdischarge + tcleaning = 10 min tfilteration = tcleaning = 10 min…

Q: explain the problems that may arise in the process

A:

Q: Discuss the Water Sachet Failure due to Change in Supplier and one thermal analysis technique for…

A: Introduction Potable sachet water (drinking water)  quality is solemnly dependent on the quality of…

Q: One of these is an advantage of Biodiesel. O All of these O Low freezing point Good as a lubricant O…

A: Biodiesel is a type of diesel fuel that is made from the usage of plants or animal waste, vegetable…

Q: In extractive distillation, why is a large concentration of solvent required in the liquid phase?…

A: Extractive distillation - it is the distillation in the presence of miscible,  high boiling,…

Q: two varieties of dryers used in the chemical Industry

A: Drying is the process by which the excess amount of moisture content present can be removed. The…

Q: Write the difference between packed bed and Fluidized bed reactors.

A: Given, it is asked to find  the difference between packed bed and Fluidized bed reactors.

Q: The following unit operations involve both mass and heat transport, EXCEPT: A. Drying B.…

A: Mass transport is defined as the movement of one or more components of a phase either within the…

Q: 1. The surface temperature of the electronic chip shown below is 75 °C and it is surrounded by…

A: Given, The surface temperature of the electronic chip, Ts = 75°C The temperature of air, Ta = 25°C…

Q: Suggest two engineering design ideas for better efficiency of a shell of the three phase separators.

A: Hello Subscriber ! You have posted multiple questions. As per our policy, we have answered the first…

Q: During a carburization process for the surface treatment of steel, how much processing time in…

A: Given: Initial carbon content (C₀) = 0.4% Desired carbon content (Cₑ) = 0.85% Carbon content at the…

Q: What is the effect of roughness on heat transfer, explain it with diagrams

A: