the answer must be:[(13/6)m + (11/9r2)] (double dot) x + (11/9)cẋ + (10/3)kx Derive the spring, mass and dampingequivalent of the system shown. Themass moment of inertia of the pulley set- up is lp. Take note that the disk will havetwo movements due to its no slipcondition. Generalized coordinate:vertical displacement of the block withmass 2m2k3kthin disk, m2r3r2cno slip2m

Answered: Image /qna-images/answer/d0231ab0-9c92-4758-89f9-600553e6eaa0.jpg

Derive the spring, mass and damping equivalent of the system shown. The mass moment of inertia of the pulley set - up is Ip. Take note that the disk will have two movements due to its no slip condition. Generalized coordinate: vertical displacement of the block with mass 2m

Derive the spring, mass and damping equivalent of the system shown. The mass moment of inertia of the pulley set - up is Ip. Take note that the disk will have two movements due to its no slip condition. Generalized coordinate: vertical displacement of the block with mass 2m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A = (A1)ï+ (A2)J + (A3)k A = 2, B = 3 B = (B1)ï + (B2)J + (B3)k ĀxB = ? Ā.B= ? JÃ×B]= ?
Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please
4. Convert the following Binary number 11010101110011112 into its Hexadecimal number equivalent.
1. The binary number 10101 is equivalent to the decimal number: (a) 19 (b) 21 (c) 35. 2. The decimal number 29 is equivalent to th binary number: (a) 10111 (b) 11011 (c) 11101.
TRANSCRIBE THE FOLLOWING TEXT IN DIGITAL FORMAT
The Maclaurin expansion of f(x) = e-5* is (-1)"x" 5"n! n=0 as above. O None of these +00 (-1)"5"x" 57x" n! n! n3D0 レ
USE this matrix num ad 200153
23. The programmer used three-point method to set up an accurate UF[3] on the part reference surface by sequentially recording points 1, 2, and 3 that are specified on the part reference surface for the three-points method in the robot system. If the programmer recorded three points used by the three-point method in the sequence of points 1, 3, 2 rather than point 1, 2, 3, then (a) the direction of x-axis is not changed (b) the direction of z-axis of UF[3] is changed (c) UF[3] setup is not accurate relative to the part reference surface (d) the origin of UF[3] is changed 24. The programmer preciously recorded all robot points P[n] for a robot task program. However, it is found that during the execution of the robot program, the robot TCP can't always precisely reach to each recorded point. Which of the following statements is correct: (a) The robot has poor accuracy (b) the robot has poor repeatability
Q2 (a) The uniformly loaded beam ABC has simple supports at A and B and an overhang BC (see Figure Q2(a)). Values X, Y and Z are given in Table Q2 (a). (i) Determine the support reaction of the beam. (ii) Draw the shear diagram and determine the point on the beam where the zero shear occurs. (iii) Draw the moment diagram and determine the points where the zero moment occurs. Table Q2(a): Parameter Parameter 1000 N/m Y 0.9 m Z 0.6 m
sketch the orthographic view of the following isometric component Note : in catia v5 software only no hand drawings Ihrough hole. 34 Dia 54 14 54 Through slot 44 20 Through slut Bearing 25
Convert the following binary numbers to decimal: (a) 10101 (b) 110011 (c) 1001001 (d) 10101011. 2. Convert the following decimal numbers to binary: (a) 25 (b) 43 (c) 65
The figure below shows a snapshot of the travelling wave in space at some arbitrary time to > 0. Based on the form of the travelling wave, which of the options below represents the correct time-varying disturbance f (t) that gave rise to this transmission from the communications tower? You may assume the wave speed is c. 2 1.5 1 0.5 0 -0.5 -1 -1.5 -2 3 5 y(x,t) 0 1 2 x (m)