Density of sea water at the surface was measured as 1040 kg/m³ at an atmospheric pressure of 1 bar. At certain depth in water, the density was found to be 1055 kg/m³. Which nearly gives the absolute pressure at that point in kPa. The bulk modulus of elasticity is 2290 × 106 N/m² Use: 1 bar= 100 kPa О а. 31068 Ob. 13541 С. 16540 d. 32659

Density of sea water at the surface was measured as 1040 kg/m³ at an atmospheric pressure of 1 bar. At certain depth in water, the density was found to be 1055 kg/m³. Which nearly gives the absolute pressure at that point in kPa. The bulk modulus of elasticity is 2290 × 106 N/m² Use: 1 bar= 100 kPa О а. 31068 Ob. 13541 С. 16540 d. 32659

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a 3 m long cantilever beam (i.e., a beam fixed at one end) that carries a 500 kg concentrated point load at the free end. Calculate the maximum tensile stress in the beam for the beam section dimensions shown below (Assume solid and homogeneous material; use g = 9.81 m/s2) give answer in N/m^2
Refer to the photo provided. Please make sure your handwriting is readable. Internal pressure and axial tensile force are applied to an open cylindrical tank 605 mm in diameter and 3.02 mm thick, resulting in the final stresses illustrated in the Mohr's circle. If a = 40.10 MPa, b = 100.06 MPa, and c = 45.05 MPa. 1. Determine the kPa value of the internal pressure. 2. What is the axial force's magnitude in kN?
A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rods (1) is 3110 μm/m. Assume initial rod lengths of L₁ = 1,250 mm and L₂ = 2,000 mm. Determine the normal strain in rod (2). (2) (1) L₁ Rigid bar 1779 μm/m 1944 μm/m 2518 μm/m 2687 μm/m 1565 µm/m B P L2 (1)
Help me with Solution, Need fast. Do not waste time. A steel beam is installed in a building when the ambient temperature is -12C. If the beam if fixed at it's ends (prevented from expanding/contracting), calculate the stress that will develop in the beam if the ambient temperature rises to +32C. State whether the stress is tension or compression. Assume E 200,000 MPa and \alpha L = 12x10-6 (/\deg C)
A bar of varying square cross-section is loaded symmetrically as shown in the figure. Loads shown are placed on one of the axes of symmetry of cross-section. Ignoring self weight, the maximum tensile stress in N/mm² anywhere is 100 mm (1)... (2) 100 kN 50->>> 50 kN 100 KN ___(1) (2)
Last three digit of id: 229
QUESTION 2 The bar shown has a cross-sectional area of A Young's modulus of E and a length of L. It is carrying a force of F. Calculate the normal stress (a) in the bar. F F O k Your unique values to use are (everybody will get different values for every question): 45 KN 4256 mm A 426 mm² 220 GPa Your mark will be based entirely on the answer you select from below. 0 = 233 MPa o=151 MPa 0=171 MPa = 190 MPa a=202 MPa a = 92 MPa 0 52 MPa 0122 MPa 0=76 MPa 0= 145 MPa 0-62 MPa o=140 MPa d=212 MPa 0106 MPa 0-100 MPa
At the limit of proportionality, a bar 30 mm wide (w) and 12 mm thick (t) elongates 2.0 mm under an axial load of 41.5 kN. The bar is 1.5 m long. If the Poisson's coefficient of the material is 0.33, determine: (a) the modulus of elasticity. E = ? (b) the variation in width. dw = ? (c) variation in thickness. dt = ?
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa
Question 13 4 pts A tank is subjected to a pressure of 50 MPa. If the thickness of the tank is 10 mm and the diameter is 2 m, calculate the tangential stress in the tank. О 250 МРа О 5000 МPа O 2500 MPa O 500 MPa
S=25
Will you be able to answer this too please