DEFLECTIONSMethod of Virtual WorkHw.21The L-shaped frame is made from two segments, each of length L andflexural stiffness EI. If it is subjected to the uniform distributed load, -determine the horizontal displacement of the end C, and the verticaldisplacement of point B. Use the method of virtual work.Hw.22

Using the virtual method: The Free body diagram after applying unit load and unit moment at the…

DEFLECTIONS R Method of Virtual Work Hw.21 The L-shaped frame is made from two segments, each of length L and flexural stiffness EI. If it is subjected to the uniform distrbuted load, determine the horizontal displacement of the end C, and the vertical displacement of point B. Use the method of virtual work.

DEFLECTIONS R Method of Virtual Work Hw.21 The L-shaped frame is made from two segments, each of length L and flexural stiffness EI. If it is subjected to the uniform distrbuted load, determine the horizontal displacement of the end C, and the vertical displacement of point B. Use the method of virtual work.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simple beam AB supports five equally spaced loads P (see figure). (Solve the problem by the method of superposition. The beam has constant flexural rigidity EI.) P p p B L L L L L 6 6 6 6 6 6 (a) Determine the deflection &, at the midpoint of the beam. (Enter the magnitude. Use the following as necessary: P, L, E, and I.) 8₁ = (b) If the same total load (5P) is distributed as a uniform load on the beam, what is the deflection 2 at the midpoint? (Enter the magnitude. Use the following as necessary: P, L, E, and I.) 8₂ = (c) Calculate the ratio of ₁ to 82.
USE AREA MOMENT METHOD TO SOLVE THIS PLEASE. THANK YOU. SHOW COMPLETE SOLUTION. The trapezoidal loading is carried by the simply supported beam AB. The beam is a steel tube with the cross section shown. Determine the displacement of the beam at midspan and the slope angle of the elastic curve at end A. Use E = 200 GPa for steel. 30 kN/m 15 KN/m 80 mm, 3m 70 mm
Analayse please
choose the right answer
Use the VIRTUAL WORK method. a.) determine the vertical displacement of joint A. Each bar is made of steel and has a cross-sectional area of 600 mm^2. Take E= 200 GPa. b.) why solving the reactions of the supports is not needed or necessary?
For the beam shown, compute (a) the slope and deflection at midspan and (b) the maximum deflection. Draw also the elastic curve. Assume El= constant. E= 200 GPa, I = | 70(106) mm² 3 kN/m A 6 m- 6 kN B 1.5 m
8-31. Determine the slope at B and the displacement at C. El is constant. Use the conjugate-beam method. P A B a Prob. 8-31 a a
7. Determine the equation of the elastic curve for the beam using the x coordinate that is valid for 0
Determine the position a of roller support B in terms of L so that deflection at end C is the same as the maximum deflection in region AB of the overhang beam. EI is constant.
A tapered bar AB of solid circular cross section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dA and de, respectively. Determine the elongation of the bar due to the load P, assuming that the angle of taper is small P da A B T dв 1 m
Compute the deflection at the midspan and at the point under load P for the beam shown using the Conjugate Beam Method
Need asap pls.