Define and show on the figure the necessary vectors and their angles for second mechanism and construct the corresponding vector-loop equation(s). please draw the vectors and angles and visually show them on mechanism you can name the angles theta1, theta2 etc. it should be looking exactly like the example( first mechanism).

Q: Draw the kinematic digrams of the following mechanisms and compute the number of Degrees of Freedom…

A: The kinematic diagram is  :

Q: Q3. For the link and slider mechanism shown in the figure VB = 2500 mm/s locate the instantaneous…

A:

Q: pls veryyyy urgent

A: hello dear !i hope you're doing well. would you rate the my solution.thanks ):-

Q: The link lengths and the value of 2 and offset for some fourbar crank-slide linkages are defined in…

A:

Q: Draw and discuss the FBD for the following system. • Label all forces and directions. • How many…

A: The free-body diagram of the given problem is shown below and the major forces and dimensions also…

Q: Compute the position and orientation of the tool point P from the given D-H table for the…

A: Basically, the Position of any object can be seen as the location like we see or use in GPS but the…

Q: Analytical mech

A: Approach to solving the question: The given system is a mechanical model with three degrees of…

Q: how J1 is 4 please count it on the graph with explain. (And when do we count the link and the j1…

A: Consider the instantaneous diagram of the mechanism as shown below. The unknown dimensions in the…

Q: Find the parametric equation of the line in figure (2), then find the parametric equation of the…

A: Given:To find:Parametric equations of the line and the cylinder.

Q: The figure shows a linkage in one position. What is the instantaneous acceleration of point P if the…

A:

Q: The figure shows a linkage in one position. What is the instantaneous acceleration of point Pif the…

A:

Q: The general linkage configuration and terminology for an offset fourbar slider- crank linkage are…

A:

Q: Given: AB = 0.1 m , CB = 0.4 m,  CD = 0.6 m,  AD = 0.8 m For the linkage shown below, CD moves back…

A: The objective of the question is to find the maximum angle that the link CD can move when the circle…

Q: Write force F2 in vector form

A:

Q: The figure below shows a four- par linkage. If a=5m, b=7m, =9m, d310m, 0=60°, p-10°, a=30° and…

A: Solution given,Q= 5m, b=7m, c=9m , d= 10m ,θ=60, ∅=10°W2= irad/sTransmission angle : Angle b/w…

Q: Qestion-1: An elliptical trammel is a double slider-crank mechanism used for drawing ellipses as…

A: Given: R3 =10 mm velocity V3 = 10 mm/sec θ3= 45 degree R1X = 20 mm R1Y = 40 mm

Q: can you do a position analysis to this mechanism whether in geometric or analythical way to be able…

A: Given:

Q: Activity 3 (1) For the linkage in Figure P4-10, calculate and plot the angular displacement of links…

A:

Q: The arrangement of cranks in a six-cylinder in-line engine is shown in the figure. The cylinders are…

A: Given the parameters:Number of cylinders, n = 6Angular positions of the cranks  = [0, 120, 240, 240,…

Q: use matrix to find solution for omega 3. find vD not in i+j form please.

A: PROBLEM has been solved and student has sought for matrix notation and magnitude wise solution of…

Q: please very urgent with count on the graph only ( j1 and link and j2)

A: Kinematic image for a pair of pliers: Kinematic image for Front Loader:

Q: Q2. A hydraulically actuated horizontal slider mechanism is illustrated in figure 2 where the motion…

A: Hydraulical horizontal slider mechanism is a mechanism which is actuated with the help of hydraulic…

Q: pls using just the rules attached in picture i need her all. solving pls veryyy urgent

A: Identify Given Information:From the image, collect data on link lengths (a, b, c, d), input crank…

Q: Given: AB = 0.1 m , CB = 0.4 m,  CD = 0.6 m,  AD = 0.8 m For the linkage shown below, CD moves back…

A: The objective of the question is to find the maximum angle that the link CD can move when the circle…

Q: 5.) A leg is placed in traction to keep it elevated and prevent it from moving as shown: Small…

A: Part (i)   A pulley transmits the load as it is. It only changes the direction but doesn't alter its…

Q: Use rotation about the fixed frame to calculate the transformation matrix for a rotation of 30°…

A: For solution refer below images.

Q: 2. For the crank-slider type linkage shown¹, you are given that link lengths |ZA| = |AZ| = 10 cm,…

A:

Q: A sliding block C moves along a horizontal line Q2C. A rotation arm Q2B is 4 ft 3 in long and…

A:

Q: c) Consider the mechanism in the next figure. The symbols r and / stand for the length of the link…

A:

Q: The link lengths and the values of 02, W2, and y for some inverted fourbar crank- slider linkages…

A:

Free undamped vibrations

Whenever an object/system displaces in either side of its equilibrium position with the help of an external/internal means, then the object/system moves regularly or randomly on both sides of its equilibrium position. This motion is called vibration. Generally, there are three types of vibration: longitudinal vibration, transverse vibration, and torsional vibration.