DC power supply converts AC signal into DC signal. A complete DC power supply block diagram has the following blocks NOT in a correct Order: 1) 2) 1. Filter 2. Transformer 3. Regulator 4. Rectifier Label the following block diagram from the list given above to construct the DC power supply correctly (You can write corresponding numbers in the box below). Vac Draw the approximate output waveform at the output of each stage (Given the waveform at the main and the load). Vout: - L M₁20100= Vout Vpc 0 Vout — Vpc Page 2

DC power supply converts AC signal into DC signal. A complete DC power supply block diagram has the following blocks NOT in a correct Order: 1) 2) 1. Filter 2. Transformer 3. Regulator 4. Rectifier Label the following block diagram from the list given above to construct the DC power supply correctly (You can write corresponding numbers in the box below). Vac Draw the approximate output waveform at the output of each stage (Given the waveform at the main and the load). Vout: - L M₁20100= Vout Vpc 0 Vout — Vpc Page 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
Draw the circuit diagram of a half-wave rectifier for producing a nearly steady dc voltage from an ac source. Draw two different full-wave circuits.
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
1.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. 2.) A 12 V rms ac supply is connected to the primary winding of a transformer with a turns ratio of 0.052. Calculate the rms secondary voltage given a voltage regulation of 4.0% 3.)Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor.
A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary a平a字a辛 R 太D。太D。太D. Select one: 0.875 Ob. 0.955 O C. 0.551 O d. 0.432 Compared with power transistors, thyristors have the following characteristic
In the full-wave rectifier circuit, the transformer has a turn ratio of 1:2. The transformer's primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50. For this circuit, determine the DC output voltage (3 significant figures)
L, m, n is only needed pls
1) a) As depicted in the figure, input voltage is 120 Volts (RMS) and diode drops are 0.7 Volts. Design this circuit with given two ac outputs and calculate turns ratio of live transformer. voltage i) 10 V ii) 100 V 2) b) Consider a circuit using Si diodes and 10 k ohms resistors. Design this clipper circuit with output ranges below; i) -0.7 V and above ii) +2.1 V and above iii) +1.4 V c) As given in the figure a clamper circuit with the input +10V- signal Vi is proposed to design. Determine the output voltage with the exact solution step by step. Sketch transfer characteristic Vo versus V₁. V₂ Vo H 2RS -10V- -2√ 01 Vo Trims
Subject : ECE
Determine the value required for each given condition if an AC voltage with an amplitude of 10 V at a frequency of 50 Hz is the source to each condition. AC meter reading for the given Choose. + AC voltage (V). V_rms (V) of a Half Wave rectifier for the given AC Choose.. + voltage as input. Average of the given AC Choose.. voltage (V). The average output voltage (V) of a Bridge rectifier for the given AC voltage as input. Choose... The average output voltage (V) of a centre tapped rectifier Choose... for the given AC voltage as input. Choose... +
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
Solve each one with steps.