Data has been gathered from a lifting system used to trans port engine parts. The sys tem cons is ts of a drum and cable. The following data was obtained when the drum lowers the load (assume cons tant acceleration). Drum diameter = 1m Mass of load = 9kg Drum Initial velocity = 0 m/s Time to des cend = 64 secs Dis tance travelled = 0.7m Cable You have been asked to use this information to determine: a) The final linear velocity of the load b) The linear acceleration of the load Load c) The final angular velocity of the drum d) The angular acceleration of the drum e) The tens ion force in the cable f) The torque applied to the drum Fioure 1

Data has been gathered from a lifting system used to trans port engine parts. The sys tem cons is ts of a drum and cable. The following data was obtained when the drum lowers the load (assume cons tant acceleration). Drum diameter = 1m Mass of load = 9kg Drum Initial velocity = 0 m/s Time to des cend = 64 secs Dis tance travelled = 0.7m Cable You have been asked to use this information to determine: a) The final linear velocity of the load b) The linear acceleration of the load Load c) The final angular velocity of the drum d) The angular acceleration of the drum e) The tens ion force in the cable f) The torque applied to the drum Fioure 1

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Only need part EGot answered for rest
answer 4 needs solution/explanation. please type the solution if you can because i cannot see handwritten sometimes. i will upvote ty Use the following data when needed: ρwater=1000 kg/m^3 , g = 9.80 m/s2 and 1 atm = 1.013 × 105 Pa.
Determine the force Prequired to maintain the 190-kg engine in the position for which 0-36%. The diameter of the pulley at Bis negligible. Answer: Pi 2.0 m 2.0 m 190 kg N
Determine the tension in the rope AC and BC ( take g=10 m/s^2)
Needs Complete typed solution with 100 % accuracy.
Problem A solid uniform ball with mass m and diameter d is supported against a vertical frictionless wall by a thin massless wire of length L. a) Find the tension in the wire. L r m Solution a) Let us first derive the expression for the tension. By Newton's First Law ΣF 0 the components of force that makes this so is ΣFT cosphi mg = 0 Simplifying this results to T= m g/ cos Analyzing the figure above, we arrive at (4) = sqrt( L 2 + 2Lr %3D cos + | By substitution, we arrive at the following: T= m ( d + 2 L )g/( 2 sqrt ( L 2 + 2Lr If the ball has a mass of 45 kg and diameter 32 cm, while the wire has a length of 30 cm. The tension is equal to T= 47 0.370 N
In rolling, if the maximum draft is 13 mm, & the coefficient of friction is Capstan is found in 0.3, thus the minimum roll radius is blanking. O Other processes 140 mm O Rolling. O 156.5 mm O forging. O 135.5 O bar drawing. O 130 mm wire drawing. O 145.5 mm Bending O 0.4215 O Deep drawing O 150 mm O extrusion. O 0.5125 O O أخرى: 144.444 mm
Determine the magnitude F, of the tensile spring force in order that the resultant of F, and F is a vertical force. Determine the magnitude R of this ver- tical resultant force. F = 120 lb 60° G ww A
A mass weighting 48 lbs stretches a spring 7 inches. The mass is in a medium that exerts a viscous resistance of A lbs when the mass has a velocity of 2 ft/sec. This system will be overdamped if A> lbs
Determine the magnitudes of the force R and couple M exerted by the nut and bolt on the loaded bracket at O to maintain equilibrium. 2.5 KN Answers: R= 57 i M = i 170 mm. 220 mm 180 mm 1.7 KN KN kN-m
Fill in the data as you complete the lab. In the table, m represents mass and r represents the distance from the fulcrum. Use a zero or a dash (–) when there is no second object on one side of a problem. Include units with all data. The image of the balancing act is scenrio 2.
1. The setup shown by the diagram below was used to calculate the force experienced by a small mass m situated at a distance r from the geometric center of a spherical shell with mass M, radius R, and a wall thickness of t. M = с dᎾ R 0 Rde A B Rsine r l r Ф p dF l If the mass is situated outside the spherical shell, the force can be calculated by integration from l = (r - R) (r+ R), as shown here: to l l=r+R R - 5 d² - T Gompert (1+²^²=R²) 21 SdF = Jae l=r-R m What would the limits of integration be if the mass were situated inside the spherical shell? Include a labeled diagram to represent this situation.