Dark Activated Switch circuit using LDR X1 9v Relay R2 1kQ COM 230v 100W V2 D1 R1 IN4007 50ka LED NO INC 230v AC .V1 -9-12v Q1 2N2222A Dark Sensor LDR Fig(3) Procedure 3-obstruct the light on LDR ,you see the led will be light ,explain the situation. 4-connect the circuit in fig3 which is the same of above plus relay .use a(12v) car lamp. 5- convert the circuit to be sensitive to light 5- What is the difference between the circuit using one transistor and tow transistor ? 11

Dark Activated Switch circuit using LDR X1 9v Relay R2 1kQ COM 230v 100W V2 D1 R1 IN4007 50ka LED NO INC 230v AC .V1 -9-12v Q1 2N2222A Dark Sensor LDR Fig(3) Procedure 3-obstruct the light on LDR ,you see the led will be light ,explain the situation. 4-connect the circuit in fig3 which is the same of above plus relay .use a(12v) car lamp. 5- convert the circuit to be sensitive to light 5- What is the difference between the circuit using one transistor and tow transistor ? 11

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. Please respond to question in attached image. Thank you.
Before you start using the unfamiliar Dimmer PPQQ2020 you decided to make an experiment with the device to better understand how the dimmer work Define the question of your experiment Define the variables of your experiment Define the hypothesis of your experiment
In this System your primary element is sending 1v - 5v to your controller and our controller is sending 4mA - 20mA to your final Element. 1) The Primary Element is sending 2.8v. Your controller is reading 2.8v. The Controller sends 5.2mA to the Final Element but nothing changes in your Process Variable. What is wrong? Controller Final Element Transmitter Wire 2) The Primary Element is sending 12v. Your controller is reading 12v. The Controller sends 0mA to the Final Element. What is wrong? Controller Final Element Transmitter Wire 3) the Primary Element is sending 3.4v. Your controller is reading 0v. The Control is not making changes when necessary, what is wrong? Controller Final Element Transmitter Wire
Quick please.
Problems I A potentiometer with a uniform resistamce per unit length of track has a total resistance of 2 k2 and a supply voltage of 10 V is connected across it. The output from the potentiometer is connected across a load of resistance 5 k2 What will be the error due to this loading when the slider is at the mid-point of the potentiometer track? -2 A potentiometer with a uniform resistance per unit length of track is to have a track length of 100 mm and used with the output being measured with an instrument of resistance 10 k2. Determine the resistance
(b) The circuit in Figure Q2 (b) below shows a rectifier circuit where Vin is a 10kHz sine wave with an amplitude of 2Vpp and RL is 10k. (i) (iii) The componet between A and B is a PN diode, sketch and label its silicon structure and explain its characteristics. Sketch the waveforms you would see at A and B and explain or sketch how you would connect your scope probes to measure them. Label your sketches clearly showing values and axis details. Comment on any similarities or differences between the waveforms at A and B.
solve both or will dislike answer
Based upon the following assumptions: V1 = 13V, V2 = 19V, R1 = 0.9kQ, R2 = 9300, R3 = 3kQ, R4 = 3.4kQ, R5 = 1.2k2. If R5 is the load resistor find VTH Answer in volts with 3 significant digits, only enter the number, don't enter the units. V1 V2
O * 33% A moodle1.du.edu.om e SIM aY The measured temperature is 173 OF and the reference is 45 °F. The voltage. in mV is Select one: O a. 4.643 O b. 4.097 O e. 3.732 O d. -3.732 Previous page Next page
Calculate for, when B=100a) VB b) VE c) IE d) IB e) Ic f) Vc g) VCE
A Dashboard Events E My Courses This course Find i0 by using current division method. R1 = 20 Q R2 = 12 Q R3 = 16 Q R4 = 24 Q Rs = 10 Q R2 R3 io 10 A( R1 Rs R4 Select one: here to search TI78 EENG250 Midterm . Ở Settings
Explain this diagram