d:3m b=2.5M C:2.5M *Analyze the structure under given loading. P-10 KN "Design members 14,12,42,45,43,23,53 *Design joints 1,2,3,4 and 5. This question is about steel structures in Civil Engineering. There is no D in question. It is P (load) a = 3m b = 2.5m c = 2.5m P = 10KN Design members : 14,12,42,45,43,23,53 Design joints 1,2,3,4 and 5 Analyze the structure under given loading.

d:3m b=2.5M C:2.5M Analyze the structure under given loading. P-10 KN "Design members 14,12,42,45,43,23,53 Design joints 1,2,3,4 and 5. This question is about steel structures in Civil Engineering. There is no D in question. It is P (load) a = 3m b = 2.5m c = 2.5m P = 10KN Design members : 14,12,42,45,43,23,53 Design joints 1,2,3,4 and 5 Analyze the structure under given loading.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two steel plates each of width 150mm and thickness 10mm are connected with three 20mm diameter rivets placed in a zig-zag pattern. The pitch of the rivets is 75 mm and gauge is 60mm. If the allowable tensile stress is 150 MPa, the maximum tensile force that the joint can withstand is
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 61 GPa] with a cross-sectional area of A₁ = 810 mm². Bar (2) is a bronze alloy [E = 103 GPa] with a cross-sectional area of A2 = 470 mm². Assume L₁=2.4 m, L₂=3.1 m, a=0.7 m, b=1.9 m, and c= 1.1 m. All bars are unstressed before the load P is applied; however, there is a 5.8-mm clearance in the pin connection at A. If a load of P = 44 kN is applied at B, determine: (a) the normal stresses 0₁, 0₂, in both bars (1) and (2). (b) the normal strains &1, 82, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. A Answers: (a) 0₁ = (STVA = a i i B 156.10 0.00256 b C MPa, 0₁ = με, €2 = mm L2 i i D 20.75 0.0002014 MPa. με.
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₁ = 700 mm². Bar (2) is a bronze alloy [E = 106 GPa] with a cross-sectional area of A₂ = 480 mm². Assume L₁=1.8 m, L₂=2.1 m, a=0.5 m, b=1.6 m, and c=0.8 m. All bars are unstressed before the load P is applied; however, there is a 3.4-mm clearance in the pin connection at A. If a load of P = 53 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains 1, 2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. (1) A Answers: (a) σ₁ = (b) 1 (c) VA = i a L₁ B b (2) L2 MPa, 0₁ = με, €2 = mm. i i D MPa. με.
i need the answer quickly
Please answer the question correctly and pleaase put the answer on the paper. Thank you Note: The tolerance is ± 1 in the third significant digit. Put the exact answer
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m Sm A B L= 6m 9o kN L-4m A= 0.04 m A = 0.0 6m² E=200 GAa E=80 GPa
Determine (approximately) the forces in the members of the truss shown below. Show your solution including units and the free body diagrams. 20 KN F 3 m A 10 kN 4 m E 20 KN 4 m D C 10 KN
b. Discuss how the figure below and determine the rigid bar BDE as used to support by two link AB and CD. 0.4 m 0.3 m B D 0.4 m 30 kN E 0.2 m The Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm2. Link CD is made of steel (E = 200 GPa) and has a cross- sectional area of (600 mm2). For the 30-kN force shown, determine the deflection a) of B, b) of D, and c) of E.
Fundamental Deformable Bodies
: Consider the truss shown in the figure below, and answer the following questions. Figure is not to scale. P P R K 5 m B C D E F - 2 m --2 m - 2 m - 2 m- 2 m-- 2 m - a) If P and R are non-zero forces and Q = 0 kN, indicate all the zero-force members in the truss. O LB O LC O KC O KD O JD O ID O IE О НЕ О НЕ O None b) Following from the situation described in Part (a), how many additional zero-force members will there be in the truss in the following situation? If the force R acting at node H is removed.
Glu-laminated beams are used to support the roof and pulley load at a warehouse. Beams span 24 feet plus an eight foot overhang over the loading area. Determine the bending stress adequacy of the beam.