D washer (2) n holes of diameter D. To reduce water consumption, a washer is installed in the shower head as shown in the figure above. The pipe diameter at point (1) is D1=1.01 cm and the shower head has n=50 holes of diameter Dn=0.89 mm. If the pressure at point (1) remains constant and all losses except for that in the washer are neglected, determine the value of the loss coefficient (based on the velocity in the pipe) of the flow reducer if its presence is to reduce the flowrate by a factor of 2. Neglect gravity.

Q: Please find the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A: Step 1:

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: Is/ are graphical representation of arrangement of geological and structural features of a…

A:

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: How can I find GH, EG and FH

A:

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: Can you help me figure out the different symbols and how many of them are there and put them in…

A: Single Pole Switch Duplex Outlet Quadruplex Outlet Electrical Outlet Fan Outlet Wall Mounted…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: Use the unit load method to calculate the vertical displacements at the quarter and mid-span points…

A: The given figure is shown below:

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: 12" 6* 12" MATHalino.com

A:

Q: but I nee

A: Draw the figure Consider a differential element of size dy

Q: R10 30 50 O. 15 R30

A:

Q: 9- The Scale The scale of a drawing is... Lo = X Lo = Lo= e= If e 1: Full size representation. e 1:…

A:

Q: 5 ft 8 ft 2 ft A -3 ft- XB 3 5 4 30 lb B P

A:

Q: order (D^2+4)y

A: Given:- (D^2+4)y=sin x To find:- reduction of order

Q: +y") dx ly

A:

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: Please find the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: Convert 0.0351 to engineering notation. O a) 35.1 × 103 O b) 3.51 × 10–2 )c) 3.51 x 10² O d) 35.1 ×…

A: Solution:- We have to convert the given number into the engineering notation, The given number is…

Q: 112 тm К30 тm ->- 30 тm -+30 тm ->-30 mт -> Рart a) Determine the moment of inertia of the shaded…

A:

Q: Dipper is another word for bucket. ) True False

A: A word or phrase that is exactly the same as another word or phrase in the same language. for…

Q: 100 N 100 N 100 100 150 250

A:

Q: Solve thee following problem step by step so I can understand in neat hand writing.

A:

Q: Y

A:

Q: Picture Name Uses

A: Name of tool - Wood Rasp Files Use - Used in carpentry for removal of excess material.

Q: The block of mass m1 = m0 is attached to a spring of elastic constant k = (m0g)/H and natural length…

A:

Q: Where do I get Ix from?

A: Bending stress formula:or, M/ = Z  {here, Z = I/y}or, Z= = 1.376 x 106 mm3W 18 x 50 has Z = 1.557 x…

Q: 12 13 12 13 14 10 Which tools that can be used to :4 draw the following shape in .AutoCAD R5 R10 R12…

A: To draw the given shape we will require the following command necessarily :- Dimension, line or…

Q: Determine external as well as internal indeterminacy

A: Given data : Number of member (m)=15Number of Joint (J)=10Number of external support reaction…

Q: There are 7 dimension commands in AutoCAD. True False

A: These are the dimension commands available in AutoCAD:

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.