(d) The tank below is cylindrical with a diameter of 10 m. The outlet is a cylindrical frictionless nozzle, with a diameter 1 m. The top of the tank is open to the atmosphere. When the level in the tank is 10 m above the centerline of the outlet, using the Bernoulli equation or otherwise determine how fast the level in the tank falling. Pcu/COE/226-13

(d) The tank below is cylindrical with a diameter of 10 m. The outlet is a cylindrical frictionless nozzle, with a diameter 1 m. The top of the tank is open to the atmosphere. When the level in the tank is 10 m above the centerline of the outlet, using the Bernoulli equation or otherwise determine how fast the level in the tank falling. Pcu/COE/226-13

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A ball weighing 1 kg is “floating" on a circular jet, as shown in the figure (ignore the wire, which is there to stabilize the weight). The jet leaving the orifice at the bottom has an upward velocity of 10 m/s, and the jet diameter at the exit is 2 cm. Assuming the jet spills sideways at 90°, find the height h at which the ball will float. Jet D1 =0.02 m W1 = 10 -
I need the answer as soon as possible
In a Francis turbine, the pressure gage in the turbine casing reads 480 kpa. The elevation above the tailrace to the center of spiral casing is 14 m. Velocity of water entering the turbine is 14 m/s. Determine the net head. Answer in m and in whole number
Fluid flows through the venture tube shown below. Pressure at section 2 is equal to 101 kPa. If pressure at point 1 is 251 kPa, determine the manometer reading h? Density of fluid and mercury are 1000 kg/m^3 and 13750 kg/m 3, respectively. section 1 section 2 mercury 15.3 m 1.861 m O 25.59 m 1.2 m O L112 m O O
3. (a) A nozzle of inlet area A₁ and exit area A2 exhausts to atmosphere. A fluid of density p enters the nozzle with pressure p₁ (gauge) and velocity u₁. Show that the force trying to separate the nozzle from the pipe is given by 2 F = P₁A₁ - pA₁u₁² whether the nozzle is frictionless or not. A₁ A₂ -1)
The 1m diameter tank is initially filled with gasoline. There is a 3.1 cm diameter orifice in the bottom. If the orifice is suddenly opened, estimate the time (minutes) for the fluid level to drop from 2m to 1.5 m. Use SG (gas) = 0.7, Cd = 0.66. answer in 2 decimal places.
Consider the figure
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. Show your illustration if required in the problem. a.0.989 b.0.98 c.0.636 d.0.629
What horizontal force is required to hold the plate stationary against the water jet? (allthe water leaves parallel to the plate).
A sealed tank containing seawater to a height of 12 m also contains air above the water at gage pressure of 5 atm. Water flows out from the bottom through a small hole. Calculate the efflux speed of the water. Note: p= 1.03 x 10³ kg/m³
kg Water (p = 1000- -) flows through the elbow below. The diameter of both the inlet and outlet is 1.1 cm, and the velocity through the nozzle is V =4.5 m/s. The outlet m³ has an angle of 0 =15 degrees. The water is at a pressure of 29 kPa (gauge). Find the magnitude of the force on the elbow. 0 V
A fan has a suction pressure of 37mm water vacuum with air velocity of 8m/s. the discharge has 230 mm of water gauge and discharge velocity of 6.89 m/s. Determine the total head of fan if air density is 1.2 kg/m³. c204