D A В E 4 m 4 m 4 m -4 m - Prob. 6–22

Q: Determine the ratio of the factored compressive load and the design compressive strength.0…

A: Answer  Calculation of ratio of factored compressive load and the design compressive strength For…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A: For the given beam, two forces and couple has to be replaced by an equivalent couple M and resultant…

Q: Assume that the loads are being transmitted to the bottom of the truss in the diagram below. For…

A: Answer  (a) Influence line diagram for member DI Consider a section passing through member DI as…

Q: Determine the Maximum positive moment (kN-m) in the beam shown Where: P = 84kN; w= 10kN/m; L1 = 3m;…

A: Differentiate equation with respect to x acix to obtain bending moment location.

Q: C-2 A uniform live load of 300 lb/ft and a single live concentrated force of 1500 lb are to be…

A: Given data:- The given uniform live load, =300 lb/ft3 The concentrated force, = 1500 lb The given…

Q: Solve for the internal reaction for each member of the truss using method of joints

A: Step 1: Step 2: Step 3: Step 4:

Q: Maximum axial force on EF.

A:

Q: The beam supports a uniform dead load of 500 N/m and a single live concentrated force of 3000 N.…

A: Given Data  Dead load = 500 N/m  Concentrated Live load = 3000 N  Find  a. Maximum positive moment…

Q: 2. Determine the smallest moment of inertia required for the beam shown, so that its maximum…

A: Please upload one question at a time

Q: 2. For the truss shown in the figure below, assume that the loads are being transmitted to the…

A:

Q: The steel truss was subjected to horizontal force 2kN at C. Find the m of AC using the method of…

A:

Q: A uniform live load of 0.25k/ft. and a single concentrated live force of 3 k are to be placed on the…

A:

Q: The dead load on the bridge girder is 800 N/m and the live load is shown below. Assume B and D are…

A: Given data: Dead load on the bridge girder=800 N/m Series of point live loads are moving on girder…

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Answer  Influence line diagram for member DI Consider a vertical section passing through DI as shown…

Q: d live load of P kN. Determine (a) the maximum positive (upward) reaction at B, (b) the maximum…

A: For the above beam, Assume W1=87N/mW2=4kN/mP=3kN

Q: Determine the maximum moment and the maximum shear in the girder bridge due to the truck loading…

A:

Q: H J K "d" kN "d" kN "c" kN "b" m G В "a/2" m "a" m 6 @ "a" m = 6*a m

A:

Q: #3 The beam is subjected to a uniform dead load of 1.2 kN/m and a single live load of P kN.…

A:

Q: Solve for the moments over the supports in the beam loaded as shown. L 을 0.3BL 0.3BL 2 L BL

A:

Q: 3- The beam - column below, which has two ends and Concentrated load Q-80 KN and compressive load…

A: Note : Since there are two questions given in a single question window. As per guidelines only 1st…

Q: N/m and a single live load of P kN. Determine (a) the mum moment created by these loads at C, and…

A:

Q: A uniform live load of 2 k/ft and a single concentrated live force of 6 k are placed on the floor…

A:

Q: FI1-1. Determine the required magnitude of force P to maintain equilibrium of the linkage at 0= 60°.…

A: Draw FBD:

Q: DI in kN; if none, enter "0."

A:

Q: Determine the reactions at the supports A and B of the compound beam. Assume there is a pin at C.…

A:

Q: The rigid beam is supported by a pin support at A and steel wires BD and CE (E-20OGPA). The steel…

A:

Q: Determine the resultant force at pins A, B, and C on the three-member frame. P=129 N q=200 N/m

A: Load P = 129 NLoad intensity q = 200 N/m

Q: #2 Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the…

A: Total length = 5+4+7+3 = 19

Q: #3 The beam is subjected to a uniform dead load of 1.2 kN/m and a single live load of P kN.…

A:

Q: 1. Compute the force in member FEF 2. Compute the force in member FED

A:

Q: в с D E F G Hinge Hinge 4 m- - 4 m+3 m--3 m- 2 m 2 m a) Determine the maximum positive moment that…

A:

Q: a. Maximum tension on member DI in kN, put "O" if none. b. Maximum compression on member DI in kN,…

A:

Q: Consider the roof truss below subjected to roof load (Lr) and wind load (W). Assume no otherloads…

A:

Q: Determine the Maximum shown Where: P = 85kN; w = 10kN/m; L1 = 4m; L2 = 10 P

A:

Q: The bridge truss shown carries the following uniform live load and concentrated live load. в с DE A…

A: Solution: Given: h = 3 m B = 8 m ULL = 15  PLL = 110

Q: #4 The beam is used to support a dead load of W k/ft, a live load of 2 k/ft and a concentrated live…

A: