D 1CD C 1AB A

Q: Answer question 2 based on the results of question 1. You have a natural gas furnace in your…

A: ENERGY CONSUMPTION BY FURNACES Natural gas furnace = 80698000 Btu Heating oil furnace = 71512440…

Q: The traffic light hangs from the cables as shown. Draw a free-body diagram on a coordinate plane for…

A: Given data Weight of light =200N Draw the free body diagram

Q: The given frame is subjected to the applied loads P and Q. Note that members ABC and CDE are…

A: Given  To Find: FAF, FBG, FDG,FEH

Q: 1 "16. You have just moved to a hot, dry climate where it is 37C and 20% rh, and the heat is…

A:

Q: Determine the magnitude of the resultant force. Express your answer to three significant figures and…

A: Data given- F = 44 lb

Q: Q1} The coefficient of friction, µ can be determined in an experiment by measuring the force F…

A: Test 1: μ1 = F / mg = 12.5 / (2 * 9.81 ) = 0.6371 μ2 = F / mg = 23.5 / ( 4 * 9.81 ) = 0.591 μ3 = F /…

Q: The car has a listed 300 horsepower, 3.5-liter engine. Express the engine size in both kW and in3 .…

A: The unit conversion from horsepower to kW is shown below.

Q: Need the 2nd question solved please. the first one has been done

A: The given tower system is as shown below, Given that,b=1F1=F2=T The resultant force is given as,…

Q: a,b,c please and thank you!

A: The objective of the question is to determine the maximum and minimum principal stresses and the…

Q: 100 lb 800 lb · ft A |C B 5 ft 5 ft

A:

Q: 30 kN | 50 kN D A BA 1m - 3 m - 2 m

A:

Q: An object having 15 kg mass weighs 14 kg on a spring balance. The value of ‘g ‘at this place 14 m/s2…

A: mass = 15kg weight on spring balance = 14 kg

Q: The force F = {450 i-200 j-700 k} lb acts at the end of the beam shown in (Figure 1). Figure 1 of 1…

A: Given data:- The force F=(450 i-200 j-700 k) lb To find:- the z, y, and z components of the moment…

Q: QUESTION 10 A Watt (W) is defined as one Joule (J) of energy per second (s): 1 W = 1 J/s. It is also…

A: The maximum range of the car is 326.1 miles.

Q: Using the coefficients of static friction indicated, determine the largest vertical force P which…

A: To find: Largest Force P that can be applied to cord without causing motion

Q: 5. The probability that a student fails the screening test for scoliosis at a local high school is…

A: Given that The probability that a student fails the screening test for scoliosis = 0.004 Total…

Q: 1- One millivolt is one millionth of a volt. (a) True (b) False

A:

Q: force F has the components Fx = 20 lb, Fy = -30 lb, ans Fz = 60 lb. What is the magnitude of the…

A: Given:Fx=20 lbFy=-30 lbFz=60 lb

Q: Determine the reactions at supports including the forces in the internal hinges (if any). Show all…

A:

Q: 1. A meter stick is found to balance at the 49.7-cm mark when placed on a fulcrum. When a 50.0-gram…

A: As meter stick is balanced when fulcrum is at 49.7 cm, this distance is the center of gravity (G) of…

Q: Some scientists believe that the collision of one or more large asteroids with the Earth was…

A:

Atomic diffusion in solids

In material science, diffusion can take place in solid, liquid, and gases. In solids, atomic diffusion can take place with the help of thermally activated and randomly vibrating atoms. The atomic diffusion in solids is complex and very slow in comparison to atomic diffusion in liquids and gases because the interatomic distance between the atoms is smaller in solids as compared to liquids and gases.