D 150 N B 80 mm 100 mm T.

Q: The system shown is in equilibrium by the applied 250 N-force. Determine the pin reaction D. Neglect…

A: Given data: The applied load is P = 250 N. The horizontal distance between A and O is x = 125 mm.…

Q: The jib crane is designed for a maximum capacity of 5 kN, and its uniform I-beam has a mass of 200…

A: To Find : The resultant force at x=0.8m. Given :  The maximum capacity is 5kN The mass of beam is…

Q: 4 kN 4) The uniform 200 kg beam AB is supported by a pin and a roller as shown. Determine the…

A:

Q: A structure formed by the two bars AB and BG, joined by means of a bolt at B. At C it has a…

A: To find : The reaction at A and G  Given :  Free body diagram

Q: Determine the maximum downward force Pmax that can be applied to wedge A that wil keep the assembly…

A: Given: The weight of block C, W = 192 N

Q: Problem 2. Consider the frame loaded as shown. If the reaction force at the roller at F is 250N,…

A:

Q: Q4/ The jib crane is supported by a pin at C and rod AB. If the load has a mass of 3 Mg with its…

A:

Q: Determine the horizontal and vertical reactions at pin A on member AB. Roller E is pinned to the…

A: Given: The weight of body, W = 1500 lb

Q: The uniform 15-m pole has a mass of 150 kg and is supported by its smooth ends against the vertical…

A: Given:m=150 KgL=15 m

Q: Q.3- If block B weighs 325N and block C weighs 175 N, determine the required weight of block D and…

A: We can see the FBD of the joint A

Q: 39 Determine the magritades of forces F, and Fy so that the particle shown in Rig. P4 is in…

A: Resolve the forces F2 and F3 along x and y axes by using the concept of vector resolution. Draw a…

Q: For the linkage shown, determine the force Q required for equilibrium when I = 18 in., M = 600…

A: The data given is, The moment on the member, M = 600 Ib.in The angle of inclination, θ= 70° Length…

Q: Determine the reactions on rollers at point A and hinge at point B, if the 39.0m and 14.0KN uniform…

A: Draw the FBD for the given figure and question conditions. The weight of the bridge will act at the…

Q: Two massless and frictionless pulleys are used to drag a large mass (m = 645 kg) up an inclined…

A:

Q: 3/91 Determine the forces on the bearings A and B if a 30-lb force on the crank is required to…

A: To findDetermine the force on the bearings A and B.GivenForce, F = 30 lbConnecting rod length, l =…

Q: 6- When holding the 15-lb equilibrium, the humorous H, assumed to be smooth, exerts normal forces Fc…

A:

Q: Cart B , which weighs 75 kN, rolls along a sloping track that forms an angle B with the horizontal.…

A: Draw the free body diagram for the above problem. Write the distances in terms of angle.

Q: Now, for the same J-shaped member, determine MA, MA and MA, the couple moments at the support about…

A:

Q: Determine the equilibrium positions of the bars for a given value of the force F.

A: Given: To find: Equilibrium positions

Q: B NGA W E DAB C H ENERAL TOS CITY A DAME OF NOTRE WIVERSITY

A:

Q: Bar GHJ is subject to a 25 lb force and is supported by a pin in a smooth slot at G, a weightless…

A: The link at H is weightlessThe weight of GHJ is

Q: The pin at B is attached to member ABC and can slide freely along the slot cut in the fixed plate.…

A: Given: The force is P=25 lb. The angle is θ=27∘. The below figure represents the free body diagram…

Q: If the mass of the flowerpot is 65 kg, calculate the tension generated in every cable for…

A: Solution:

Q: Determine the horizontal and vertical components of reaction on the beam caused by the pin at B and…

A:

Q: Determine the magnitude of the reactions at pin A, pulley D is friction free, and the cylinder…

A:

Q: 2. Determine the angle 0 at which the bar AB is in equilibrium if W = 5x.yz N. Neglect the weight of…

A:

Q: Determine the horizontal and vertical components of reaction on the beam caused by the pin at B and…

A:

Q: Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power…

A:

Q: Determine the horizontal and vertical components of reaction at pin A and the tension at cable AB.…

A: Given:-             The equllibrium equation is:

Q: Determine the reactions at A and B. 400 lb/ft 6 ft 4 ft- H .6 ft 300 lb/ft B

A:

Q: The uniform 21-m pole has a mass of 105 kg and is supported by its smooth ends against the vertical…

A: Given:-m=105 kgPole height= 21mTo find:-Magnitude of the reations at A and B

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: The jib crane is designed for a maximum capacity of 9 KN, and its uniform I-beam has a mass of 260…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Determine the reactions on rollers at point A and hinge at point B, if the 39.0m and 14.0KN uniform…

A:

Q: Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA.…

A:

Q: Q.4. Determine the weight of the engine that can be supported at point A if a tension of 5000 N in…

A: Tension in cable AB is 5000N

Q: Determine the force (F) which applied to ring A in order to keep the 250 lb *.cylinder B in…

A: As it is given that cylinder is in equilibrium, then the forces and moments acting on it are in…

Q: The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts…

Q: The uniform 18-m pole has a mass of 110 kg and is supported by its smooth ends against the vertical…

A:

Q: The pin at B is attached to member ABC and can slide freely along the slot cut in the fixed plate.…

A: The free-body diagram of the member ABC can be drawn as below, Here Cx and Cy are the horizontal…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.