The cylindrical tank with a spherical end-cap has an outer radius of 2.54m and a wallthickness of 53 mm. if the tank is pressurized to 1.45 MPA. What is the circumferentialstress (MPA) in the cylinder?2 m

Answered: Image /qna-images/answer/95dd8b33-9635-4cdd-a27e-faa247246680.jpg

Answered: cylindrical tank with a spherical…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A 20 cm long ram has its entire length engaged in a cylinder. The diameter of the ram is 10 cm and the gap between the ram and the cylinder is 1mm which is filled with SAE 30 oil at 40°C. The ram travels at 54. Find the frictional resistance(force) of the surfaces.
The force F required to hold the plug in its position ( from given figure)
Challenge Problems 8. A solid resin cone (SGresin = 0.50) is placed vertically in a vat of liquid (SGnq = 1.2) as shown on the right. Determine: a) the depth h through which the cone sinks (h not drawn to scale). b) whether the cone will be stable or unstable in this position. im 2m
Question 2 A closed vertical drum is filled to a depth 0.5m with petrol of specific gravity 0.78. The height of the drum is 0.7m and its diameter 0.4m. When stationary, air of atmospheric pressure occupies the portion of the drum. if the drum is rotated about its vertical axis at a speed just sufficient for the depth on the axis to be zera, calculate: 1. The speed of rotation at this condition KQuestion 2 of 30
requirement : a good understandable handwriting and answer in step by step procedure with good arrangement
A bubble whose inside diameter is 0.06 in has a surface tension of 0.003 lb/ft. What is the pressure difference between the inner and outer side of the bubble? Select the correct response: 0.112 psi O .0.012 psi 0.017 psi 0.117 psi
Two vats are connected by a submerged pipe with a square cross-section, as shown in the image attached. A hinged valve in the centre of the square pipe prevents the fluid in both vats from mixing. The valve door is square and has a cross sectional area of L X L, and the hinge is at the top of the door. The fluid depth in the first tank is h1 and the depth in the second tank is h2. The fluid in Vat 1 exerts a horizontal force, F1, on the valve door when it is closed. Express F1 in terms of h1. The fluid in Vat 1 exerts a Moment M1 on the valve door (acting about the hinge at the top of the door) when it is closed. Express M1 in terms of h1. Considering the fluid in both vat1 and vat2, express the net moment on the door in terms of h1 and h2 when it is closed. If the valve can withstand a moment of Mmax before opening, find the maximum possible height difference between the fluid in vats 1 and 2.
Solve for the pressure differential in Pa if the temperature inside a 3.46m vertical wall is 23.52°C, and at the outside is -16.27°C. Assume equal pressures at the top. Express your answer in 3 decimal places.
PROBLEM 1- The pressure at point m in the figure shown was increased from 70 * kPa to 105 kPa. This causes the top level of mercury to move 20 mm in the sloping tube. What is the inclination,? m 3 degrees 13 degrees 23 degrees 33 degrees 43 degrees none of the above Hg S-B- 13.6 e
Problem 1. The gauge pressure of the air in the tank shown in the figure below is meası red to be 65 kPa (fluids’ densities as follows: PH20 = 1000 Kg , Poil = 742 Kg/m³, Phg = 13650 Kg/m³). Determine the differential height а) h of the mercury column Oil 65 kPa Determine the resultant force per b) unit depth acting on the quarter of circumference (radius R=15 cm) at the left bottom corner of the tank. 75 cm Air Water |30 сm h - Mercury H%3D75 cm
Provide the step by step solution in solving for the Hydrostatic Force on Curved Surfaces
Provide the step by step solution in solving for the Hydrostatic Force on Plane Surfaces

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

cylindrical tank with a spherical end-cap has an outer radius of 2.54m and a wall kness of 53 mm. if the tank is pressurized to 1.45 MPA. What is the circumferential ss (MPA) in the cylinder?|