cylindrical tank of 10 mm thickness is filled with water that exerts an internal pressure of 3.0 MPa. Consider that the Poisson’s ratio is 0.30 and that the modulus of elasticity is 110 GPa. Calculate the change in diameter caused by the pressure of water if the inside diameter of the tank is 5.0 m

Q: .109 A circular metallic rod of length 250 mm is placed between two rigid immovable walls as shown…

A:

Q: A 30mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is…

A: Do=800.5mm Di=800mm E=200GPa

Q: Figure P-251 A L= 5 ft L= 3 ft 2 ft 6000 4 ft 4 ft

A:

Q: A rectangular tube has an outside width of 100 mm, an outside depth of 150 mm, and a wall thickness…

A: σ=MyII=BH312-bh312=100×150312-80×130312=13478333.33mm4M=1.4k-m

Q: 20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 1081 MPa…

A:

Q: Q3: A plastic rod is 200mm long and 15mm in diameter. If a tensile load of 300N is applied to it,…

A: Given data in question  Load Diameter  Length Modulus of Elasticity  Poissons ration To find out…

Q: Question 4 The state of stress is showing as a particular point in a stressed body. The diameter of…

A: Given- State of stress is given- σx=100 MPaσy=-50 MPaτxy=50 MPa It is needed to find the diameter…

Q: Determine the plastic moment (Mp) and shape factor (k) of a thin square tube of side 200 mm and wall…

A:

Q: A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P =…

A: We will use formula of elongation. use formula of relation between E and G.

Q: Steel railroad rails 8m long are laid with a clearance of 4mm at a temperature of 10°C. At what…

A:

Q: WATE IS PLACED IN A HYDRAULIC PRESS INITIALLY OF 140 kPa ABSOLUTE, THE PRESSURE IS NCREASED TO…

A: Given data- Initial Pressure = 140 kPa Final Pressure = 222538 kPa Bulk Modulus (K) = 2.5 GPa To…

Q: Find the bulk modulus of elasticity of a liquid if a pressure of 150 psi applied to 10 ft of the…

A: Increase in pressure, ∆P=150 psiInitial Volume, V=10 ft3Decrease in Volume, dV=0.02 ft3

Q: 9. The thin-walled tube is subjected to an axial force of 40 kN. If the tube elongates 3 mm and its…

A:

Q: The figure shows a homogeneous. rigid block weighing W = 14 kips that is supported by three…

A: Let PS is force in steel rod and PB is force in bronze rod From condition of static equilibrium :…

Q: A circular aluminum tube with a length of L= 420 mm is loaded in compression by forces P (see…

A:

Q: A solid plastic rod has a diameter of d = 19 mm and a length of L = 500 mm. An axial load of P= 24…

A:

Q: A cylindrical tank for transporting compressed gas has an inside diameter of 360 mm and a wall…

A:

Q: Water is placed in a hydraulic press initially at 140kPa absolute, the pressure is increased to…

A: Given,  Bulk modulus (k)= 2.5GPa = 2.5×10⁹ Pa bulk modulus(k)= Increase of pressure / Volumetric…

Q: material has a grain diameter of 0.0005 cm. What height of capillary rise will you expect? The…

A: Radius=diameter/2 r=0.000005/2 r=2.5*10-6 m

Q: As shown, three steel wires, each 27 mm2 in area, are used to lift a mass M. Their unstretched…

A:

Q: 2 m Steel Steel rod Bronze rod 3 m Bronze 55 kN Area (mm²) 485 970 2 m E (GPa) 200 120 Steel a(/°C)…

A:

Q: Problem 1. A 40 Newton force is applied to the brake pedal as shown in the figure. If the line of…

A: Given data,   Force (P) = 40 N   Diameter of piston( d) = 5 mm         To find out the compressive…

Q: Find the change in volume of 5 ft3 of water at 80 0F when subjected to a pressure increase of 368…

A:

Q: A circular rod, circular in cross-section tapers from 2.5 cm diameter to 1.25 cm diameter in a…

A:

Q: e the axial stress of the aluminum rod in the figure if the temperature of the steel rod is y 30…

A: The temperature of steel rod is increased by 30 degree.

Q: A solid 2.1 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

A:

Q: The stresses shown in the figure act at a point in a stressed body. Determine the normal and shear…

A: Given :   To Find : Determine the normal and shear stresses at this point in the inclined plane ?

Q: The beam shown below is carrying a vertical shear force v. S IF

A: Given Data:Vu=53000 Nb=100mmh=170mmE=220GpaTo Calculate: Maximum shear stress.

Q: A Newtonian fluid has the following velocity field: V = x² yî + 2æy? z} – yz³k The rate of shear…

A:

Q: A solid circular rod with a diameter of d = 19 mm is shown in the figure. The bar is made of an…

A: Given data: Diameter of the rod (D) = 19mm Modulus of elasticity of the aluminium (E) = 70 GPa = 70…

Q: A rigid block having a mass 5 Mg is supported by three rods symmetrically placed, as shown in the…

A:

Q: 2. The solid rod with two rigid caps attached to its ends is subjected to an axial force P. If the…

A:

Q: As shown, three steel wires, each 26 mm in area, are used to lift a mass M. Their unstretched…

A:

Q: Prob3.2. Calculate the strain energy in a bar 3 m long and 40 mm in diameter when it is subjected to…

A: Length of the bar= 3mDiameter =40mmTensile load= 100kNE= 2.05×10⁵ N/mm²

Q: A l-m long steel bar (E = 200 GPa) of 10 x 10 mm dimension fixed at both ends is heated to 90°C from…

A:

Q: A cylindrical metal bar of 12 mm diameter is located by an axial force of 20 kN results in a change…

A:

Q: An initially rectangular element of material is deformed as shown in the figure. The shear strain in…

A: To find the shear  strain in the section

Q: The 5-m-long tube is made of an elastic perfectly plastic material as shown in the figure below…

A:

Q: 1. Determine the normal stress at bar AC. Use diameter of bar AC = 215 mm. 500 N 2 m 2 m

A:

Pressure and Stress