CWDE converts word to double-word extending using EAX: AX. in which the sign of the 16-bit register, AX, is extended into the 32-bit register, EAX. What is the value for registers AX and EAX after executing the mnemonic opcode/operand instruction below? MOV EAX, 0 MOV AX, 0x429FCDA5 CWDE O a. AX=CDA5 EAX 0000CDA5 Ob. AX=CDA5 EAX EFFFCDA5 OC. AX=CDA5 EAX=FFFE000 Od. AX= CDA5 EAX=FFFFCDA5

CWDE converts word to double-word extending using EAX: AX. in which the sign of the 16-bit register, AX, is extended into the 32-bit register, EAX. What is the value for registers AX and EAX after executing the mnemonic opcode/operand instruction below? MOV EAX, 0 MOV AX, 0x429FCDA5 CWDE O a. AX=CDA5 EAX 0000CDA5 Ob. AX=CDA5 EAX EFFFCDA5 OC. AX=CDA5 EAX=FFFE000 Od. AX= CDA5 EAX=FFFFCDA5

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Find the pyhsical destination adress of last instruction below. MOV BX,0AAH MOV AX,1BBH MOV DS,AX MOV[BX],AX
Let's assume %ecx = 0x000FFD0E and %eax= 0x000FED25 (Hexadecimal representation). What is the value in %ecx after the following instruction? orq %eax, %ecx Provide answer in hexadecimal representation. Acceptable answer format: 000003FD or 0x000003FD
Q2:- (A) Find the phicycal address if (BP) = 0100H , (SI) = 0200H , (SS) = 2000H and a displacement of 10H, of the instruction MOV AL, [BP+SI+10H]. Which the name of Addressing Modes?
There are four condtioinal flags in embedded systems, C which is carry, Z which is zero, V which is overflow and N which is negative. Flnd value of each letter (flag) after instruction is run. 1) r1=oxoo0o o0ol and r2=D0XFFFF FFFE Adds ro, rl, r2. 2) r1=ox7oo0 o0ol and r2=DoxFooo o000 Subs ro, rl, r2. Expert Answer ® W hp
Write down the values of destination operands and flags after the execution of each instruction: .code bh, 1 mov sub bh, 1 (а) вн 3 ? ZF = ? mov dl, o sub dl, 1 ; (b) DL = ? SF = ? mov ch, 11111111b add ch, 1 ; (c) CH = ? CF = ? al, 0 mov sub al, 1 ; (d) AL = ? CF = ? cl, 01111111b mov add cl, 1 ; (e) CL = ? OF = ? ah, 10000000b mov neg ah ; (f) CF = ? OF = ?
Given the typical stack frame set up, what will be in edx after executing this instruction: mov edx, [ebp + 4]? Hint: It is NOT any of the selections above.
SP=1239H, SS=9876H, the physical address is AAAFOH Non of them 1BC06H 0AAAFH 99999H if BX=1000, DS=0400, and AL=EDH, for the following instruction: MOV [BX] + 1234H, AL. the physical address is 6324H O 4244H 4234H 6234H 6243H O
Write HCL code for the signal D_stall in the PIPE implementation.Pipeline register D must be set to bubble for a mispredicted branch ora ret instruction. As the analysis in the preceding section shows,however, it should not inject a bubble when there is a load/use hazardin combination with a ret instruction:bool D_bubble =# Mispredicted branch (E_icode == IJXX && !e_Cnd) ||# Stalling at fetch while ret passes through pipeline# but not condition for a load/use hazard!(E_icode in { IMRMOVQ, IPOPQ } && E_dstM in { d_srcA,d_srcB }) && IRET in { D_icode, E_icode, M_icode };
What is the value for the 32-bit register EAX after executing the mnemonic opcode/operand instruction MOVZX? (This mnemonic opcode/operand instruction converts 8-bits to 32- bits) MOV EAX, O MOV AL, 0X54C9BF5 MOVZX EAX, AL EAX= FFFFFFF5 а. EAX= 000000F5 O b. EAX= 00000FF5 С. EAX= 00000BF5 d.
Based on the diagram below, what is the result for register AX after executing the mnemonic opcode/operand instructions? MOV AX, 200h MOV BX, 10O0h MUL BX AX BX DX AX CF OF 200h X 100h (X) The resulted AX is 0002. а. The resulted AX is 0000. b. The resulted AX is 1111. Ос. The resulted AX is FFFF. d.
Do you know what occurs when an instruction is rejected? A software-managed TLB would outperform a hardware- managed TLB in the following scenarios:
For the given values of D, shr, shr_in, Id, and clk, indicate the register's Q value. Dis 111, shr_in is 0, shr is 1, Id is 0, and Q is 101. clk rises. What does Q become? Function table thr Id | Register function IP shr in- 0 0 Maintain 01Lood 0 Shuft-right 1Maintain 13 12 i1 0 13 12 it 0 13 12 it 10 she st 4xl 4x1 4xl Block ymbol DFF OFF DFF to she in 3-bit ahift-rht/lend ragister she at ahirightad ld Pegiter O 010 O 110 O 101 O 111