ctions on the given beam

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: Pictured below is a multiplication problem worked out using the Egyptian method and Egyptian…

A: Consider the given diagram and see row 1 and row 2.

Q: 1-) b. 1+j 1 Evaluate a. 1+j

A: Ans(a)  j2=-1 Divide by 1-j both sides 1-j1+j×1-j1-j (1-j)21-j2=1+j2-2j2=-2j2=-j

Q: Convert to isometric drawing mark point A as the lowest point

A: use a 30-60 triangle to create the isometric  figure ng follow the left, front and top illustration…

Q: draw the orthographic view of the drawing and identify the alphabets of lines used by pointing out…

A:

Q: (degree) Calculate the measure of the angle in degrees marked in white for the following figure 24…

A:

Q: Hi, -26.088 or 333.911 is INCORRECT for Ox please recheck

A:

Q: Briefly describe the action taken by the following G&M command blocks assuming absolute coordinates.…

A:

Q: The given sketch is a view of modified “Plate" one view. Sketch the 2D sketch of the below figure…

A:

Q: Draw the orthographic views of the following isometric figure.

A:

Q: Draw the orthographic views of the following isometric figure

A: Given  3D model isometric view To find Orthographic view

Q: create 2 fourbar designs that include the dimensions and angle of motion

A: It is asked to draw four bar mechanism with given motion

Q: 30r 20dls 20 10r 20 20 30 150 100

A:

Q: dy Solve the differential equation cos(z) dz

A:

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A:

Q: A rock is spit out of a fire. Its initial temperature is 414 degrees. After exactly 8 minutes, it…

A: Introduction: Newton's law of cooling, which is a function of the cooling constant and time, is…

Q: Consider FIG-DD in the appendix.   Note: For Blocks “A” & “B” & “C”: The mass of “A” is 30 kg.…

A:

Q: Consider the floating point system F and answer the following questions. Your solution to each part…

A: y=cos6xwe should use dx slice & the washer methodwasher have outer radius R=…

Q: Find the limit. NOTE: Enter an exact limit if it erists. If the limit does not exist, indicate that…

A:

Q: i need the answer quickly

A:

Q: What is the angular velocity (rad/sec) if z-64.77 cm 70 cm Vertical ee Select one a. 101.85 b. 76.39…

A:

Q: Q3: Chose and mark a datum point on the given work-piece (shown in figure 1) and mark out the…

A:

Q: Q13. For the beam AB shown in the image below, it is supported by a fixed collar (on smooth rod)…

A: a = 2.1 m b = 2.1 m Force F = 160 N Intensity w = 194 N/m find support moment at point A

Q: In the following diagram, which lines are indicated by D? Ø20.00 60.00 A Select one: E B A.…

A: To find : which lines are indicated by D

Q: 20.00 40.00 60.00 FRONT 60.00 00'0 20.00 00'0

A: If straight lines are drawn from various points on the contour of an object to meet a plane, the…

Q: 20. Find the radius of gyration with respect to its axis of the solid generated by revolving the…

A:

Q: A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2…

A: Dear student,                     According to the guidelines, I am allowed to answer only…

Q: An automobile tire is 65.0 cm in diameter. How fast (rpm) does the wheel turn on the axle when the…

A:

Q: Q4 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 1:1.

A: Required Front view, Top view and side view are drawn using first angle method of projections.

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: What does the expression VB/A mean? O A. O B. Absolute velocity of point B. OC. Velocity of point B…

A: Relative velocity: The rate of change in relative position of one object with respect to another…

Q: 20 R3 Which tools that can be used to :3 draw the following shape in .AutoCAD 37 23 43 R3 dimension,…

A:

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: Please write what each line of G- code means for each line. Thanks

A: G codes representation in the given program

Q: Draw Front and Side and top with all dimensions please

A: Draw the top view and side view first as shown in the below attached image:

Q: Analyse the codes below and work out the final position of the cutting tool. G90 G21; S600 M03; GO0…

A: It is required to determine final position of cutting tool

Q: DRAW THE ISOMETRIC FIGURES OF THE ORTHOGRAPHIC DRAWINGS BELOW. ADD DIMENSIONS AND LEADERS

A: According to the details provided in the question, we need to draw an isometric view

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A: Original Number = 6748.3 After Round off up to three significant number = 6750

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.