Criteria for a frame: Osupport loads all two force members all multiforce members some two force members at least one multiforce member all pin connected some pin connections Osupports other than hinges, roller, rocker O supports may be normal supports only pin loaded distributed loads may be applied Origid

Q: When are the singularity functions used?

A: Solution-  We can observe that the shear and bending moment expressions get increasingly complicated…

Q: show the integration process

A: To show the integration process

Q: Determine the Centroid of 3 Areas.

A:

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: Please explain Part B properly. any classification table is there? How is the order and level…

A: Given: Misclosure= 15mm Total length,K= 10 Km Required: Order of levelling

Q: Define integer ambiguities.

A: Answer The integer ambiguities are used in GPS & GNSS surveys.

Q: For the given structures, determine the degree of indeterminacy. 7. A 7

A:

Q: The Lowest level of design pattern is called a. Design Patterns b. Architectural Design Patterns c.…

A: The lowest level of design pattern is called  d. Analysis pattern

Q: What is a box model? Give the equation to represent box model.

A: The Urban air quality models has been called box models. The Figure is a schematic graph of a box…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: What does the reductent diagram look like?

A: What does the reductent diagram look like?

Q: CEM IV 42.5 N: Define what each word/number/letter is?

A: 1.CEM-  CEM means CEMENT .Cement is the binding material from which concrete is prepared. Cement act…

Q: A frame ABCDE is subjected to forces Po, Pe, and a moment Mcas shown in the Figure below. If Po = 10…

A:

Q: what is the difference between 42 square meter and 42 meter square

A: It is needed to differenciate between 42 square meter and 42 meter square.

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: introduction abbout the purpose of SYMBOLS FOR AGRICULTURAL BUILDINGS AND STRUCTURES

A: Introduction- Any structure utilised in farming activities, including residences to house family…

Q: Discuss  General Methodology

A: Methodology -  The methodology is the overall examination technique that diagrams the manner by…

Q: Determine the shape factor

A: Given:- An I- section is given  To determine:-  The shape factor of the given section

Q: Defline APP.

A: Basic Concept Introduction- APP- It is the short form or abbreviation for the application.

Q: classification of rivers

A: Classification of Rivers

Q: Value the line theorem in the context of scale drawing.

A: Scale drawing: In the scale drawing, an object has exactly the same shape as the original object but…

Q: For the given structures, determine the degree of indeterminacy. 1. ♫

A: This question is related to the Structure analysis

Q: i need all parts of question on the right hand corner solve I STATED FILL IN THE BLANKS.

A: Only 3 subparts can be answered at a time according to guildlines. Please resubmit the question…

Q: [Choose ] solve equilibrium equations simultaneously ensure you have an equal number of unknowns and…

A: Understand force flow. Understand the math behind structural analysis (concepts like virtual work…

Q: Explain Phase Estimating

A: This hybrid or phase estimation technique is a technique of a project’s costs and the duration…

Q: How are the sensitive parameters identified?

A: The process of determining probability of a variable of interest affected when value of one or more…

Q: concept of 5D modeling.

A: The  graphical and non graphical information created using information models is known as 5D…

Q: Define Relative Density.

A: Relative density or specific gravity:

Q: For the given structures, determine the degree of indeterminacy. 3. 3

A: The given structure has two fixed supports at ends and one roller support in the middle. The fixed…

Q: Can you please redo this and explain how you got what you got? I dont understand concept and show…

A: To draw a cross-section AA' and BB' for the given section.

Q: Explain with the help of labeled sketch if applicable the different types of scale

A:

Q: There are 7 dimension commands in AutoCAD. True False

A: These are the dimension commands available in AutoCAD: