Create a schematic from the PCB.

Q: Ex. 94. See Figure 94. Challenging exercise? Given a 8.00 kOhm potentiometer, V_AC=100.0 volts,…

A:

Q: An FWR using a centre-tapped Transformer Supplies an average voltage of 120V to a 250 kΩ load…

A: A)Average output voltage of FWR is =2Vmπ=120 VVm=120×π2Vm=188.5 V

Q: Determine the readings of two ammeters – moving coil and rectifier systems with a single-period…

A: The Permanent magnet moving coil (PMMC) instrument is used to measure D.C voltage and D.C currents.…

Q: Series Resistance Microammeter (SRM) is one of the techniques in HVDC measurement: a) Draw an…

A:

Q: Q1) The buck converter has an input of 50 V and an output of 25 V. The switching frequency is 100…

A:

Q: 5- The frequency of the output voltage obtained from three-phase Wye/Delta connected rectifier is :…

A:

Q: Find the mesh currents in the following circuit. 40 2 j102 rell ww 40/30° V -j20 2 50/0° V

A: The given circuit is,

Q: 1 V + Vx 202 ww Find the power received by each of the four elements. 1Ω 2Vx

A:

Q: • Task/ Job Breakdown Identification of Potential Hazards Preventative Measures to Overcome the…

A: Hazard- Hazard identification is part of the process used to evaluate if any particular situation,…

Q: 400 V is the input voltage given to a chopper, the required output is 650 V. The thyristor is…

A: DC-DC Converter: It will transfer the DC power from one circuit to another circuit at the required…

Q: Give a conclusion about clipper circuits and clamper circuits.

A: The clipper circuit is one in which the signal cannot exceed the value of fixed magnitude. The…

Q: E. A series circuit consisting of a 50 – ohm resistor, 0.5 – henry inductor, and a 100 – microfarad…

A:

Q: How output current is represented in an equivalent circuit of photovoltaic module? O a. IDH O b. I…

A: The basic single diode equivalent circuit model is shown below:

Q: What is the importance of the charecteristic curve in PN Junction

A: Characteristics of pn junction diode

Q: A load is connected in the Full Bridge rectifier circuit (Four Diodes). Used transformer primary…

A: According to the question, for a bridge rectifier, we need to calculate a) How many % of conduction…

Q: is the simplest way of producing a source of lower EMF from a source of higher EMF.

A:

Q: what is the use of DC/DC tension converter DC/DC booster MT3608

A: Types of mostly used DC DC Converter Step up Converter ( Boost converter) Step Down Converter (…

Q: +20 V Ipss = 12 mA Vp =-3 V 91 ΜΩ V; oAH 10 ΜΩ 1.1 kQ

A:

Q: The type of output voltage from a Solar PV module is a. DC b. AC

A: In thi question we will write solar PV module output voltage...

Q: Q5/ What is static VAR Compensator? Draw its schematic diagram. What are the two tasks of Thyristor…

A:

Q: A resistor Ra is in series with a voltage source Va. Draw the circuit. Label the voltage across the…

A: Given: To draw the circuit and Volt-ampere is shown as:

Q: o +16 V Rp22.4 ka R 2.1 MQ 10 uF G Ipss = 8 mA Vp = -4 V 5 uF R, 2270 ka Rs 1.5 k2 C 20 µF

A: In the given circuit we note that 4.2 R1  = 2.1MΩR2  = 270ΩRD = 2.4KΩRs   = 1.5C1  = 5μFC2  =…

Q: Plot the output voltage for a period of time for the input voltage Vi in the figure. (Note: the…

A: Diode is a non-linear device. In has two terminals P and N. P is positive i.e. Anode and N is…

Q: I have one (1) AC source, four (4) diodes, and one (1) thyristor. In this case, I would like to…

A: Given: Components: One thyristor Four diodes One AC source To find: Design a circuit to obtain a…

Q: One component that does not need to be installed in the correct orientation is a: a. Resistor b.…

A:

Q: A load of 10 ohms was connected to a 12-volt battery. The current drawn was 1.18 amperes. What is…

A: As per the guidelines of Bartleby we supposed to answer first question only for remaining questions…

Q: Design a 5th order Butterworth LPF with a cutoff frequency of 20kHz. Show hand calculation Overall…

A: Given: A 5th order Butterworth LPF has a cut-off frequency of 20 kHz. To find: Design the filter by…

Q: 1 X(s) s+1 Y(s) s+ 4 3.

A:

Q: An AC voltage controller with common cathode has O a. two diodes to be conducted at a time O b. one…

A: AC voltage controller is uses the combination of the SCR and the diode to control the AC voltage.

Q: Question A 3-phase full converter, fed from 3-phase, 400 V, 50 Hz source is connected to load R = 10…

A: 3-phase full converter- 3-phase, 400 V, 50 Hz source- R=10 ohm, Output current is ripple free,…

Q: A charging circuit that will deliver constant DC current will be designed. The input of the circuit…

A:

Q: What are the differences on using NI Multisim to the actual evaluation of circuits?

A: Multisim is a simulation program. It is used to test any electrical and electronic circuit. It is…

Q: Design the single-phase half wave controlled rectifier has a purely resistive load of R=100 and the…

A: In this question, we need to design a single phase half wave controlled rectifier. The average…

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.