Course Name & Code: Signals & Systems (CNET-221) 3. Consider an LTI system with impulse response h[n], and input x[n] as shown in figure-5. Solve and draw the output y[n] for the mentioned system. h[n] X[n] 1 0.5 0.5 -1 1 n -1 Figure- 5

Q: In which method of fault diagnosis ,the input test signal is applied to each stages individually ? O…

A: The correct answer is dynamic testing.

Q: What is modulation? Why is it done? Describe one of the types of amplitude modulation

A:

Q: What is the name of the signal which is indicated by the red line? 4- O A) Feedback B) Disturbance…

A: The given feedback system is non unity negative feedback system.   Here they have mentioned the…

Q: a) Design a magnitude digital Comparator that compares two 2-bit unsigned binary numbers find out…

A: define  comparator

Q: The standard test signals used in control system analysis is: O Unit step signal O All of the…

A:

Q: -at A signal FlE) = 2e ult) is applicd to the input of. System have frequency Determine the required…

A: The input signal in the frequency domain is calculated as shown below:…

Q: The output from a sensor ranges from a minimum of 10 mV to a maximum of 200 mV as the measurand…

A: An instrumentation amplifier allows an engineer to adjust the gain of an amplifier circuit without…

Q: A) Choose the correct answer. 1) For purposes of measuring length, the human torso was a convenient…

A: since the company policy allows us to answer only three subparts of a question. please upload the…

Q: B) Find the output response when the input is unit step function? RI * Figure (1)

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: (d) It is given that the propagation delay of the components are as follows: adder is 30 ns,…

A: According to the question, for the given DFG as shown below We need to find total execution time…

Q: Q1) Determine Ic,VCE, Icisat) and VCE(cut off). Also, construct DC load line and plot Q-point.…

A:

Q: In a Schmitt-trigger circuit, the output is a digital signal that stays at a high voltage level when…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: 3) For a circuit described by the state diagram of figure: 0/0 1/0 00 01 0/1 0/1 0/1 1/0 10 1/0 1/0…

A:

Q: Home work what s meant by Nyquist rate what s meant by Pulse Moduletina need PM ?

A: Given,  We have two questions. First one is nyquist rate, and second one is pulse modulation. Please…

Q: Mention several names of electronic devices that use the pulse signal processor in their work, and…

A: There are many analog and digital electronic devices which are used in digital signal processing…

Q: Derive reciprocity and electrical symmetry conditions in terms of [T| and [g] parameters

A:

Q: Q6) Consider the circuit shown in figure S, assume that V Q6a) ID(on) (in mA) is A) 0.02 B) 2 C)…

A: Given the circuit, as shown below: Given Vz=8 V, RD=4 kΩ 1. We need to find ID in mA. 2. We need to…

Q: Find the output voltage of an R/2R ladder DAC for a binary code (11001101). Assume Rf = 2R and ON…

A:

Q: - An experimenter uses a 10-bit A/D having a range from -5 [V] to +5 [V] to digitize a 35.0 [mV]…

A:

Q: A hex-to-7-segment decoder can be implemented as shown in Figure. Digits 0 to 9 are displayed the…

A: To display 10 to 15 We use hexadecimal format  10 represent as A similarly Others

Q: Match between column A and column B Column A Column B 1)--------- is tus one consideration in the…

A: 1  - C    : Accuracy 2  - D     : Repeatability 3 - E       : Tolerance 4  -A      : Sensitivity 5 -…

Q: Consider Batcher- Banyan switch with 32 inputs and 32 outputs a. What is the number of stages?

A: For the given Batcher- Banyan switch we need to compute number of stages which are required in the…

Q: Suppose a DAC of certain number of bits having range from 1-11V has a step size of minimum 50 mV.…

A:

Q: 06) Consider the circuit shown in figure 5, assume that V Q6a) ID(en) (in mA) is: A) 0.02 B) 2 C)…

A: The circuit diagram is shown below, Where,RD = 4kΩandVZ =8 V

Q: In moving coil instruments, is proportional to the coil current. Consider a 9.4-bit ADC and full…

A:

Q: Which of the following statement(s) is true for a gain response technique A. The breakaway point…

A: In this question we need to choose a correct option.

Q: 01. For a discrete time system x(n) is shown in figure, 1.5 05F 12 Sketch the following signals: a)…

A: X(n) discrete signal  First we Shifted value Then Scaling Shifting Find value first X(n+2) Then…

Q: 5- What is the effect of increasing k in First Order Systems Analysis on time constant & error ?…

A: The effect of increasing K in the first-order system is in step-2.

Q: Please check

A:

Q: - Signal conditioning element - This takes the output of the sensing element and converts it into a…

A: A signal conditioning circuit is that circuit which is used to convert one form of signal to other…

Q: c. Sketch the zero-pole plot and the direct form II diagram of the completed design out of part b.…

A:

Q: The transfer function of an LVDT is 2 mV/mm and the maximum core motion is +14 cm. From +1 cm to…

A:

Q: 3) For the circuit shown in the following figure, Io - I3 are inputs to the 4:1 multiplexer. R (MSB)…

A: Given:I0-I3 are input to the 4:1 multiplexer. R (MSB) and S are control bits. To find :The output Y.

Q: A typical digital signal processing (DSP) system is given in figure below. ADC has DOMHZ sampling…

A: consider the given question;

Q: Answer the following . Using PCM, encode the analog data below. Assume Vmax and Vmin as 5V and…

A:

Q: You are to design a 4-bit arithmetic unit that consists of a 4-bit adder/subtractor circuit. The…

A: 4bit adder/subtractor : If we want to subtract B from A then we can do addition of A and complement…

Q: Why is the R-2R ladder DAC design better than a binary-weighted DAC design, particularly if you…

A: Binary Weighted DAC:             By using binary weighted resistors in the inverting adder circuit,…

Q: Another of the blocks in the diagram is labelled sample-and hold. (i) Explain the purpose and…

A: All the physical signal are analog in nature. To process such a signal using a DSP (Digital Signal…